HP FlexFabric 5700 User Manual (English)

To Next Page

To Previous Page

Step Command Remarks

nssa-only

tag

tag |

type

type ] *

8. (Optional.) Configure OSPF

to redistribute the default

route.

default-route-advertise

summary cost

cost

By default, OSPF does not

redistribute the default route.

This command redistributes the

default route in a Type-3 LSA. The

MCE advertises the default route

to the PE.

9. (Optional.) Configure filtering

of advertised routes.

filter-policy

acl-number

export

[

protocol [ process-id ] ]

By default, redistributed routes

are not filtered.

10. (Optional.) Configure the

default parameters for

redistributed routes (cost,

route number, tag, and type).

default

{

cost

cost |

tag

tag |

type

type } *

The default cost is 1, the default

tag is 1, and default type of

redistributed routes is Type-2.

11. Create an OSPF area and

enter OSPF area view.

area

area-id

By default, no OSPF area is

created.

12. Enable OSPF on the

interface attached to the

specified network in the area.

network

ip-address

wildcard-mask

By default, an interface neither

belongs to any area nor runs

OSPF.

Configuring IS-IS between an MCE and a PE

Step Command Remarks

1. Enter system view.

system-view

N/A

2. Create an IS-IS

process for a VPN

instance and enter

IS-IS view.

isis

[ process-id ]

vpn-instance

vpn-instance-name

N/A

3. Configure a network

entity title.

network-entity

net

By default, no NET is configured.

4. Redistribute VPN

routes.

import-route

protocol [ process-id |

all-processes

allow-ibgp

] [

cost

cost-type

{

external

internal

} |

[

level-1

level-1-2

level-2

] |

tag

tag ]

By default, IS-IS does not

redistribute routes from any other

routing protocol.

If you do not specify the route level

in the command, the command

redistributes routes to the level-2

routing table by default.

5. (Optional.) Configure

filtering of advertised

routes.

filter-policy

acl-number

export

[

protocol [ process-id ] ]

By default, IS-IS does not filter

advertised routes.

6. Return to system view.

quit

N/A

7. Enter interface view.

interface

interface-type

interface-number

N/A

8. Enable the IS-IS

process on the

interface.

isis enable

[ process-id ]

By default, no IS-IS process is

enabled.

Configuring EBGP between an MCE and a PE

Step Command Remarks

1. Enter system view.

system-view

N/A

2. Enter BGP view.

bgp

as-number N/A

Need help?

Do you have a question about the HP FlexFabric 5700 and is the answer not in the manual?

HP FlexFabric 5700 Specifications

General

Category	Switch
Power Device	Internal power supply
Model	FlexFabric 5700
Uplink Ports	4 x 10 Gigabit SFP+
Form Factor	Rack-mountable
Routing Protocol	OSPF, BGP, RIP, IS-IS, PIM, IGMP, VRRP, RIPng, OSPFv3, PIM6
Remote Management Protocol	SNMP, CLI
Features	IPv6 support, ACL, QoS, VLAN, LLDP, sFlow, RMON
Compliant Standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.3ad, IEEE 802.3x
Power Redundancy	Yes
Operating Temperature	0 °C to 45 °C
Operating Humidity	10% to 90% non-condensing
MAC Address Table Size	32K entries