To Next Page

To Previous Page

# The MCE uses port Ten-GigabitEthernet 1/0/3 to connect to PE's port Ten-GigabitEthernet

1/0/1. Configure the two ports as trunk ports, and configure them to permit packets carrying

VLAN tags 30 and 40 to pass.

[MCE] interface ten-gigabitethernet 1/0/3

[MCE-Ten-GigabitEthernet1/0/3] port link-type trunk

[MCE-Ten-GigabitEthernet1/0/3] port trunk permit vlan 30 40

[MCE-Ten-GigabitEthernet1/0/3] quit

# Configure port Ten-GigabitEthernet 1/0/1 on the PE.

[PE1] interface ten-gigabitethernet 1/0/1

[PE1-Ten-GigabitEthernet1/0/1] port link-type trunk

[PE1-Ten-GigabitEthernet1/0/1] port trunk permit vlan 30 40

[PE1-Ten-GigabitEthernet1/0/1] quit

# On the MCE, create VLAN 30 and VLAN-interface 30, bind the VLAN interface to VPN

instance vpn1, and configure an IP address for the VLAN interface.

[MCE] vlan 30

[MCE-vlan30] quit

[MCE] interface vlan-interface 30

[MCE-Vlan-interface30] ip binding vpn-instance vpn1

[MCE-Vlan-interface30] ip address 30.1.1.1 24

[MCE-Vlan-interface30] quit

# On the MCE, create VLAN 40 and VLAN-interface 40, bind the VLAN interface to VPN

instance vpn2, and configure an IP address for the VLAN interface.

[MCE] vlan 40

[MCE-vlan40] quit

[MCE] interface vlan-interface 40

[MCE-Vlan-interface40] ip binding vpn-instance vpn2

[MCE-Vlan-interface40] ip address 40.1.1.1 24

[MCE-Vlan-interface40] quit

# On PE 1, create VLAN 30 and VLAN-interface 30, bind the VLAN interface to VPN instance

vpn1, and configure an IP address for the VLAN interface.

[PE1] vlan 30

[PE1-vlan30] quit

[PE1] interface vlan-interface 30

[PE1-Vlan-interface30] ip binding vpn-instance vpn1

[PE1-Vlan-interface30] ip address 30.1.1.2 24

[PE1-Vlan-interface30] quit

# On PE 1, create VLAN 40 and VLAN-interface 40, bind the VLAN interface to VPN instance

vpn2, and configure an IP address for the VLAN interface.

[PE1] vlan 40

[PE1-vlan40] quit

[PE1] interface vlan-interface 40

[PE1-Vlan-interface40] ip binding vpn-instance vpn2

[PE1-Vlan-interface40] ip address 40.1.1.2 24

[PE1-Vlan-interface40] quit

# Configure the IP address of the interface Loopback 0 as 101.101.10.1 for the MCE and as

100.100.10.1 for PE 1. Specify the loopback interface address as the router ID for the MCE and

PE 1. (Details not shown.)

# Enable OSPF process 10 on the MCE, and bind the process to VPN instance vpn1.

[MCE] ospf 10 router-id 101.101.10.1 vpn-instance vpn1

Questions and Answers:

Need help?

Do you have a question about the HP FlexFabric 5700 and is the answer not in the manual?

HP FlexFabric 5700 Specifications

General

Category	Switch
Power Device	Internal power supply
Model	FlexFabric 5700
Uplink Ports	4 x 10 Gigabit SFP+
Form Factor	Rack-mountable
Routing Protocol	OSPF, BGP, RIP, IS-IS, PIM, IGMP, VRRP, RIPng, OSPFv3, PIM6
Remote Management Protocol	SNMP, CLI
Features	IPv6 support, ACL, QoS, VLAN, LLDP, sFlow, RMON
Compliant Standards	IEEE 802.1D, IEEE 802.1Q, IEEE 802.1p, IEEE 802.1s, IEEE 802.1w, IEEE 802.3ad, IEEE 802.3x
Power Redundancy	Yes
Operating Temperature	0 °C to 45 °C
Operating Humidity	10% to 90% non-condensing
MAC Address Table Size	32K entries