EasyManuals Logo

HP ProBook 430 G1 User Manual

HP ProBook 430 G1
139 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #96 background imageLoading...
Page #96 background image
BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the
download is complete. If no instructions are displayed, follow these steps:
1. From the Start screen, type e, and then click File Explorer.
2. Click your hard drive designation. The hard drive designation is typically Local Disk (C:).
3. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains
the update.
4. Double-click the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.
5. Complete the installation by following the on-screen instructions.
NOTE: After a message on the screen reports a successful installation, you can delete the
downloaded file from your hard drive.
Using MultiBoot
About the boot device order
As the computer starts, the system attempts to boot from enabled devices. The MultiBoot utility, which is
enabled at the factory, controls the order in which the system selects a boot device. Boot devices can
include optical drives, diskette drives, a network interface card (NIC), hard drives, and USB devices.
Boot devices contain bootable media or files that the computer needs to start and operate properly.
NOTE: Some boot devices must be enabled in Computer Setup before they can be included in the
boot order.
You can change the order in which the computer searches for a boot device by changing the boot
order in Computer Setup. You can also press esc while the “Press the ESC key for Startup Menu”
message is displayed at the bottom of the screen, and then press f9. Pressing f9 displays a menu that
shows the current boot devices and allows you to select a boot device. Or, you can use MultiBoot
Express to set the computer to prompt you for a boot location each time the computer turns on or
restarts.
Choosing MultiBoot preferences
You can use MultiBoot in the following ways:
To set a new boot order that the computer uses each time it is turned on, by changing the boot
order in Computer Setup.
To dynamically choose the boot device, by pressing esc while the “Press the ESC key for Startup
Menu” message is displayed at the bottom of the screen, and then pressing f9 to enter the Boot
Device Options menu.
To use MultiBoot Express to set variable boot orders. This feature prompts you for a boot device
each time the computer is turned on or restarted.
86 Chapter 7 Computer Setup (BIOS) and Advanced System Diagnostics

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP ProBook 430 G1 and is the answer not in the manual?

HP ProBook 430 G1 Specifications

General IconGeneral
Form factorClamshell
Product typeLaptop
Product colorBlack, Silver
Country of originChina
Bus typeDMI
Tjunction100 °C
Processor cache3 MB
Processor cores2
Processor modeli3-4005U
System bus rate5 GT/s
Processor familyIntel® Core™ i3
Processor seriesIntel® Core™ i3-4000 Mobile Series
Processor socketBGA 1168
Processor threads4
Processor codenameHaswell
Processor frequency1.7 GHz
Processor cache typeSmart Cache
Processor lithography22 nm
Processor manufacturerIntel
Processor front side bus- MHz
PCI Express slots version2.0
Processor operating modes64-bit
ECC supported by processorNo
PCI Express configurations4x1, 1x4
Thermal Design Power (TDP)15 W
Maximum number of PCI Express lanes10
Motherboard chipset-
Memory slots2x SO-DIMM
Internal memory4 GB
Memory clock speed1600 MHz
Memory form factorSO-DIMM
Internal memory typeDDR3-SDRAM
Maximum internal memory16 GB
AC adapter includedYes
Intel segment taggingEnterprise, Professional
HDD interfaceSATA
Storage mediaHDD
Total storage capacity500 GB
Compatible memory cardsSD
Number of HDDs installed1
Display diagonal13.3 \
Display resolution1366 x 768 pixels
Native aspect ratio16:9
Display number of colors16.78 million colors
On-board graphics card ID0xA16
Discrete graphics card modelNot available
On-board graphics card modelIntel® HD Graphics 4400
On-board graphics card familyIntel® HD Graphics
Maximum on-board graphics card memory2 GB
On-board graphics card base frequency200 MHz
On-board graphics card DirectX version12
On-board graphics card dynamic frequency (max)950 MHz
Audio systemDTS Sound+
Front camera resolution1280 x 720 pixels
Wi-Fi standards802.11b, 802.11g, Wi-Fi 4 (802.11n)
Bluetooth version4.0
Ethernet LAN data rates10, 100, 1000 Mbit/s
Charging port typeDC-in jack
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
eSATA/USB 2.0 ports quantity0
Pointing deviceTouchpad
Recovery operating systemWindows 8 Pro
Operating system installedWindows 7 Professional
Processor ARK ID75105
Processor package size40 x 24 x 1.5 mm
Intel ME Firmware Version9.5
Supported instruction setsAVX 2.0, SSE4.1, SSE4.2
Intel Smart Connect Technology version1.00
Intel Smart Response Technology version0.00
Battery capacity44 Wh
Battery life (max)8.5 h
AC adapter power45 W
AC adapter frequency50 - 60 Hz
AC adapter input voltage100 - 240 V
Cables includedAC
Storage temperature (T-T)-15 - 60 °C
Operating temperature (T-T)5 - 35 °C
Storage relative humidity (H-H)10 - 90 %
Operating relative humidity (H-H)20 - 85 %
Sustainability certificatesRoHS, EPEAT Silver, ENERGY STAR
Weight and Dimensions IconWeight and Dimensions
Depth233.5 mm
Width325 mm
Height21 mm
Weight1500 g

Related product manuals