HP Scanjet 7000 User Manual

If the problem persists after verifying the above items, follow these steps:
1. Press the Power switch to the off position, and then disconnect the power cable from
the scanner.
2. Wait 30 seconds.
3. Reconnect the power cable to the scanner, then press the Power switch to the on
position.
See also
Check the cables
Reset the scanner
If you receive an error message similar to Scanner initialization failed or Scanner not
found when trying to use the scanner, you should reset the scanner.
To reset the scanner, follow these steps:
1. Close the HP Smart Document Scan Software and HP Scanner Tools Utility, if they
are open.
2. Disconnect the USB cable that connects the scanner to the computer.
3. Turn the computer off, wait 60 seconds, and then turn on the computer.
4. Reconnect the USB cable to a USB port on the back of the computer.
• Make sure that the USB cable is connected to the back of the scanner correctly.
The trident icon on the USB cable faces up when the cable is properly connected
to the scanner.
• Try connecting the USB cable to a different USB port on the back of the computer.
Scanner has stopped working correctly
If the scanner stops scanning, follow these steps. After each step, start a scan to see if
the scanner is working. If the problem persists, proceed with the next step.
1. A cable might be loose. Ensure that both the USB cable and power supply are properly
connected.
Use the cable that was included with the scanner. Another USB cable might not be
compatible with the scanner.
2. Ensure that the scanner is receiving power.
a. Check that the green LED on the power supply case is on.
b. If the green LED is not on, ensure that power is available to the power outlet or
surge protector that the power supply is plugged into.
c. If power is available to the power outlet or surge protector but the green LED is
still not on, the power supply might be defective. Contact
www.hp.com/support
for assistance.
3. Unplug the power cable from the power source, wait 60 seconds, and then plug it
back in.
4. Restart your computer.
Chapter 5
30 Troubleshooting

HP Scanjet 7000 Specifications

General

Storage temperature (T-T)	-40 - 60 °C
Operating temperature (T-T)	10 - 35 °C
Storage relative humidity (H-H)	0 - 90 %
Operating relative humidity (H-H)	15 - 80 %
Package weight	10200 g
Sustainability certificates	ENERGY STAR
Input voltage	100-240 V
AC input frequency	50 - 60 Hz
Power consumption (typical)	40 W
Display	LCD
Scanner type	Sheet-fed scanner
Product color	Black, Silver
Film scanning	-
Color scanning	Yes
Grayscale levels	256
Input color depth	48 bit
Maximum scan size	216 x 864 mm
Output color depth	24 bit
ADF scan speed (b/w, A4)	40 ppm
ADF scan speed (color, A4)	35 ppm
Optical scanning resolution	600 x 600 DPI
Duplex ADF scan speed (b/w, A4)	80 ipm
Duplex ADF scan speed (color, A4)	70 ipm
Safety	IEC 60950-1, CCC, GOST, BSMI, NOM
Minimum scan size	50.8 x 73.6mm
Image formats supported	BMP, JPG, PNG, TIF
ISO A-series sizes (A0...A9)	A4, A5, A6, A8
Scanning media types supported	Card stock, Envelopes, Plain paper
Maximum ISO A-series paper size	A4
Auto Document Feeder (ADF) media weight	49 - 120 g/m²
Scan to	E-mail
Sensor type	CCD
Scan drivers	ISIS, TWAIN, WIA
Scan file formats	BMP, DOC, HTM, JPG, OPF, PDF, PNG, RTF, TIFF, TXT, UNICODE, WPD, XLS, XPS
Daily duty cycle (max)	2000 pages
Auto document feeder (ADF) input capacity	50 sheets
USB version	2.0
Standard interfaces	USB 2.0
Minimum RAM	512 MB
Mac compatibility	No
Minimum processor	1.3 GHz
Minimum storage drive space	300 MB
Minimum system requirements	USB 1.1 CD-ROM 1024x768 SVGA
Compatible operating systems	Windows 7 Windows Vista Windows XP Professional (32/64-Bit) Windows XP Media Center Windows XP Home Windows 2000
Windows operating systems supported	Windows 2000, Windows XP Home, Windows XP Professional, Windows XP Professional x64
Electromagnetic compatibility	FCC, CISPR, ANSI, CAN/CSA–CISPR, EN, AS/NZS CISPR, CNS

Weight and Dimensions

Depth	280 mm
Width	320 mm
Height	246 mm
Weight	7280 g