EasyManua.ls Logo

HQUA HQUA-PN02DC - User Manual

HQUA HQUA-PN02DC
11 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
HQUA
Instruction Manual
For Spa Light
HQUA-PN02DC
Section 1 Safety Information
Electrical Safety
Negligence to these instructions may result in serious injury or death.
Always disconnect the power to the spa light at the circuit breaker before
servicing the light. Failure to do so could result in death or serious injury due to
the electrical shock.
Grounding Plug
• This product use 12V-15V AC as the power source, which must be grounded and
protected by a ground-fault circuit interrupter (GFCI) to reduce the risk of electrical shock.
Contact a qualified electrician if you cannot verify that the receptacle is protected by a
GFCI.
• Do not use an appliance leakage current interrupter (ALCI) in place of a GFCI since the
ALCI will not protect people.
Electric Shock

Table of Contents

Questions and Answers

  • V
    Valerie EvansJul 30, 2025
    What to do if my HQUA HQUA-PN02DC LED pool light does not light up at the beginning?
    • C
      christiemooreJul 30, 2025
      If your HQUA Swimming Pool Lighting LED pool light isn't lighting up, there could be a few reasons. First, check the power source to ensure it's properly connected. Next, examine the connection, referring to step 2 of the installation process. If neither of those resolves the issue, it's possible the LED pool light is damaged; in this case, contact HQUA for further assistance.
  • C
    claudia88Aug 5, 2025
    What to do if my HQUA HQUA-PN02DC Swimming Pool Lighting LED pool light does not light up or is dim after a while?
    • C
      Clayton EdwardsAug 6, 2025
      If your HQUA Swimming Pool Lighting LED pool light is not lighting up or appears dim after some time, several factors could be at play. Begin by checking the wiring connection (without power) to ensure it is secure. If the issue persists, it could indicate that the LED lights have failed or the GFCI has tripped. In either of these cases, contact HQUA for further assistance.
  • A
    Anthony MartinAug 13, 2025
    How to fix HQUA Swimming Pool Lighting RC01 controller that is not working?
    • C
      curryjacquelineAug 13, 2025
      If your HQUA Swimming Pool Lighting RC01 controller isn't working, the most likely cause is a dead battery. Replace the old battery with a new 23A/A23 battery.
  • P
    Patricia OrtegaAug 21, 2025
    Why is there water inside my HQUA HQUA-PN02DC?
    • E
      Emma ElliottAug 21, 2025
      If you notice water inside your HQUA Swimming Pool Lighting, there's no need to worry. This is acceptable and a safety feature. The light has a unique waterproof layer that protects it, so no action is required.

Summary

Safety Information

Electrical Safety

Covers warnings about negligence, injury, death, and disconnecting power.

Grounding Plug

Details power source requirements, GFCI protection, and ALCI limitations.

General Information

Other Cautions

Advises against opening the light, throwing, dragging, and staring directly at the LEDs.

System Components

Lists and describes the main components of the LED light system.

Specification

Provides technical details such as wattage, voltage, luminous flux, color changing, and dimmability.

Installation

Outlines the step-by-step procedure for installing the LED spa light.

M4 Remote Controller Operation

Explains how to use the remote controller to manage light modes, brightness, and speed.

Troubleshooting

After-Sales Service

Our Commitment

Specific Warranty Coverage

Details the 2-year limited warranty for material and workmanship defects.

Part Number List

HQUA HQUA-PN02DC Specifications

General IconGeneral
ModelHQUA-PN02DC
CategorySwimming Pool Lighting
Power36W
Voltage120V AC
IP RatingIP68
MaterialStainless Steel
Beam Angle120 degrees
Lifespan50, 000 hours
TypeLED

Related product manuals