COMPLIANCE AND APPROVALS
Hunter Industries hereby declares that this product is in 
compliance with the essential requirements and other relevant 
provisions of Directive 2014/53/EU (Radio Equipment 
Directive). Contact Hunter Industries for complete  
compliance information.
 
FCC Notice
This equipment has been tested and found to comply with 
the limits for a Class B digital device pursuant to Part 15 
of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses, and 
can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is 
no guarantee that interference will not occur in a particular 
installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by 
turning the equipment o and on, you are encouraged to try to 
correct the interference by taking one or more of the following 
measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit dierent 
from that of which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for 
help.
This device complies with part 15 of FCC rules. Operation is 
subject to the following two conditions:
1.  This device may not cause harmful interference.
2. This device must accept any interference received, including 
interference that may cause undesired operation.
Changes or modications not expressly approved by Hunter 
Industries could void the user’s authority to operate this device. 
If necessary, consult a representative of Hunter Industries Inc. 
or an experienced radio/television technician for additional 
suggestions.
To satisfy FCC RF Exposure requirements for mobile and base 
station transmission devices, a separation distance of 20 cm 
or more should be maintained between the antenna of this 
device and persons during operation. To ensure compliance, 
operation at closer than this distance is not recommended. The 
antenna(s) used for this transmitter must not be co-located or 
operating in conjunction with any other antenna or transmitter.
Innovation, Science and Economic Development Canada 
(ISED) Compliance Notice
This device contains licence-exempt transmitter(s)/ 
receiver(s) that comply with Innovation, Science and Economic 
Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
1.  This device may not cause interference, and
2. This device must accept any interference, including 
interference that may cause undesired operation of the 
device.
Le présent appareil est conforme aux CNR d’Innovation, 
Sciences et Développement économique Canada applicables 
aux appareils radio exempts de licence. L’exploitation est 
autorisée aux deux conditions suivantes:
1.  L’appareil ne doit pas produire de brouillage, et
2. L’utilisateur de l’appareil doit accepter tout brouillage 
radioélectrique subi, même si le brouillage est susceptible 
d’en compromettre le fonctionnement.
Certicate of Conformity to European Directives
Hunter Industries declares that the irrigation 
controller complies with the standards of 
the European Directives of “electromagnetic 
compatibility” (2014/30/EU), “low voltage” (2014/35/EU) and 
“radio equipment” (2014/53/EU).
This symbol means the product must not be discarded 
as household waste and should be delivered to an 
appropriate collection facility for recycling. Proper 
disposal and recycling help protect natural resources, human 
health, and the environment. For more information on disposal 
and recycling of this product, contact your local municipality, 
disposal service, or the shop where you bought this product. 
 RC004IGA2CLAN     10/19
RESIDENTIAL & COMMERCIAL IRRIGATION 
|
 Built on Innovation
®
Learn more. Visit hunterindustries.com
For complete setup information, scan the QR code or visit hunterindustries.com.
© 2019 Hunter Industries Inc. Hunter, the Hunter logo, and all other trademarks are property of Hunter Industries, 
registered in the U.S. and other countries.