How to fix a Husqvarna 340 that has difficulty starting?
If your Husqvarna Chainsaw is hard to start, try these solutions: adjust the L screw, check if the air filter is blocked, ensure the choke is working properly, and inspect for a worn choke pivot or valve. Also, verify that the fuel filter and fuel line are not blocked. Other potential issues include a seized piston ring or a blocked impulse channel.
Why is my Husqvarna Chainsaw flooding when engine not running?
If your Husqvarna Chainsaw is flooding when the engine is not running, it could be due to a worn needle valve, a needle valve set too high, or a needle valve assembly sticking.
Why is the carburettor leaking fuel on my Husqvarna 340?
If your Husqvarna Chainsaw's carburettor is leaking fuel, it could be due to a loose or faulty fuel pipe, a hole in the diaphragm, a worn needle valve, a needle valve assembly sticking, a needle valve set too high, a leak in the metering system, or a loose cover on the carburettor pump side.
Why does my Husqvarna 340 engine stall when throttle is released?
If your Husqvarna Chainsaw engine stalls when the throttle is released, it might be due to: * Adjusting the L and H screws. * A faulty pump diaphragm. * A needle valve set too high or a needle valve assembly that is sticking. * Faulty diffuser jets.
What to do if my Husqvarna 340 Chainsaw does not accelerate?
If your Husqvarna Chainsaw does not accelerate, consider the following potential issues: * Adjust the L and H screws. * Check for a blocked air filter, fuel tank vent, or fuel filter. * Ensure the fuel line isn't blocked and the fuel hose isn't loose or damaged. * Inspect for a blocked impulse channel. * Examine the carburettor pump side for a loose cover or faulty pump diaphragm. * Look for a leaking air intake hose or loose carburettor mounting bolts. * Verify that the needle valve isn't set too low and the metering system is correctly assembled. * Check for a sticking needle valve assembly, faulty diffuser jets, or a blocked silencer.
Why won't my Husqvarna 340 Chainsaw run at full throttle?
If your Husqvarna Chainsaw won't run at full throttle, it could be due to several reasons: * Adjust the H screw. * A blocked air filter, fuel tank vent, or fuel filter. * A blocked or leaking fuel line or impulse channel. * A loose or damaged fuel hose. * A loose cover on the carburettor pump side, or a faulty pump diaphragm. * A leaking air intake hose or loose carburettor mounting bolts. * A needle valve set too low, a damaged or incorrectly assembled metering system, or a sticking needle valve assembly. * A leaking control diaphragm/cover plate or a blocked silencer.
Why is my Husqvarna Chainsaw carburettor leaking fuel?
If the carburettor of your Husqvarna Chainsaw is leaking fuel, it could be due to several reasons: * Check for a loose or faulty fuel pipe. * Inspect the diaphragm for any holes. * Examine the needle valve for wear or sticking. * Ensure the needle valve assembly is not sticking and is set at the correct height. * Look for any leaks in the metering system (air or fuel) or a loose cover on the carburettor pump side.
General| Cylinder Displacement | 40.8 cm³ |
|---|---|
| Weight | 4.7 kg |
| Fuel Tank Volume | 0.5 liters |
| Oil Tank Volume | 0.25 liters |
| Chain Pitch | 3/8" |
| Bar Length | 33-40 cm / 13-16 in |
Guidance on checking and maintaining safety features for safe operation.
Rules for choosing, maintaining, and using cutting equipment to minimize kickback.
Definition of kickback and techniques to avoid it, including safe cutting practices.
Instructions for mixing fuel, selecting oil, and safe fuelling procedures.
Step-by-step guides for starting cold and warm engines.
Procedure for safely stopping the chain saw engine.
To Next Page
