Why is the Error LED flashing on my Husqvarna Trimmer battery charger?
The Error LED flashing on the battery charger indicates a temperature deviation. Use the battery charger only when the surrounding temperature is between 5 °C (41 °F) and 40 °C (104 °F).
What to do if Husqvarna 536LiL charger does not start?
If the charger for your Husqvarna Trimmer doesn't start and no LEDs come on when the battery is attached, consider the following: * Check for a defective connection between the charger and battery. Ensure the power plugs are clean and undamaged. * The battery may be defective. Check the battery start. * The charger may be defective. Disconnect the charger from the mains outlet for at least 1 minute, then reconnect it. Verify that the fan starts and the green LED illuminates for about 3 seconds. If not, replace the charger.
What to do if my Husqvarna 536LiL will not start?
If your Husqvarna Trimmer isn't starting, several components could be the cause. Here's what you should check: * Inspect the battery. * Inspect the fuse. * Inspect the cables. * Inspect the safety switch. * Inspect the breaker. * Inspect the electric motor. If the issue continues after checking these, consider changing the control unit.
What to do if the Error LED flashes on my Husqvarna Trimmer?
If the Error LED is flashing, it could be due to several reasons: The power trigger and the activate button are pressed at the same time, overload, or temperature deviation. Release the power trigger and the machine will become active. For overload, remove the battery and the trimmer head from the grass. For temperature deviation, allow the machine to cool down.
What to do if Husqvarna Trimmer charger shows red warning sign?
If a red warning sign flashes on the charger when the battery is attached to your Husqvarna Trimmer, it could be due to: * A defective connection between the charger and the battery. Ensure the power plugs are clean and undamaged. * The battery temperature is too high. Allow the battery to cool down in the charger for 1-5 minutes. * The ambient temperature is too low. Ensure the ambient temperature is above 5°C. * The battery temperature is too low. Ensure the battery temperature is above 5°C. * A defective battery. Verify the battery's condition by pressing the battery start button; at least one green LED should illuminate. If not, replace the battery. * A defective charger. Disconnect the charger from the mains outlet for at least 1 minute, then reconnect it. Check that the ...
What does it mean when the Error LED is flashing on my Husqvarna 536LiL Trimmer battery charger?
If the Error LED is flashing on your Husqvarna Trimmer's battery charger, it means there's a temperature deviation. Use the battery charger only when the surrounding temperature is between 5 °C and 40 °C.
Why is the Error LED flashing on my Husqvarna Trimmer?
If the Error LED flashes on your Husqvarna Trimmer, it could be due to: * The power trigger and the activate button being pressed simultaneously. Release the power trigger to activate the machine. * An overload. Remove the battery and the trimmer head from the grass. * A temperature deviation. Allow the machine to cool down.
Why is the green activate LED flashing on my Husqvarna 536LiL?
If the green activate LED is flashing on your Husqvarna Trimmer, it indicates low battery voltage. Charge the battery to resolve this.
What to do if Husqvarna Trimmer product stops when applying work load?
If your Husqvarna Trimmer stops when you apply a workload, it may be due to defective power connectors. Ensure that the power connectors between the battery and the product are clean and undamaged.
What to do if Husqvarna 536LiL Trimmer warning sign flashes after start then stops?
If a warning sign on the keypad of your Husqvarna Trimmer flashes after you start it, and then the product stops, it could be due to several reasons: * The power trigger was pushed during start. Avoid pushing the power trigger when starting the product. * There is water in the main switch signal connector. Disassemble and dry the main switch connector, and then reassemble it. * There is a short circuit in the keypad. Replace the keypad. * There is a short circuit in the main switch. Replace the main switch.
Provides essential safety guidelines for operating power tools.
Covers personal safety measures and protective equipment.
Discusses safe usage, maintenance, and care of power tools.
Details required personal protective equipment for safe operation.
Safety information specific to the battery and charger.
Safety guidelines and precautions for handling the battery.
Safety guidelines and precautions for using the battery charger.
Describes the machine's safety features and their checks.
Explains the function of the control panel and its indicators.
Details the mechanism preventing accidental trigger operation.
Safety precautions for using cutting attachments and guards.
Safety advice and precautions specific to the trimmer head.
How to check battery capacity and status indicators.
Information about the battery charger and its operation.
Procedures for starting and stopping the machine safely.
Important safety guidelines to follow during operation.
A schedule for troubleshooting common issues with the machine.
Provides essential safety guidelines for operating power tools.
Covers personal safety measures and protective equipment.
Discusses safe usage, maintenance, and care of power tools.
Details required personal protective equipment for safe operation.
Safety information specific to the battery and charger.
Safety guidelines and precautions for handling the battery.
Safety guidelines and precautions for using the battery charger.
Describes the machine's safety features and their checks.
Explains the function of the control panel and its indicators.
Details the mechanism preventing accidental trigger operation.
Safety precautions for using cutting attachments and guards.
Safety advice and precautions specific to the trimmer head.
How to check battery capacity and status indicators.
Information about the battery charger and its operation.
Procedures for starting and stopping the machine safely.
Important safety guidelines to follow during operation.
A schedule for troubleshooting common issues with the machine.
General| Battery Voltage | 36 V |
|---|---|
| Cutting Width | 33 cm |
| Handle Type | Loop Handle |
| Power Source | Battery |
| Noise Level | 93 dB(A) |
| Type | Battery Trimmer |
| Blade Type | Line |
To Next Page
