What to do if Husqvarna 536LiL Trimmer warning sign flashes continuously?
If a warning sign on the keypad of your Husqvarna Trimmer flashes continuously, it may be due to: * The temperature being too high. Wait for the product to cool down (max. 5 minutes). * The temperature of the control unit or battery being too low. Ensure that the product and battery are not colder than -10°C.
What to do if Husqvarna 536LiL charger does not start?
If the charger for your Husqvarna Trimmer doesn't start and no LEDs come on when the battery is attached, consider the following: * Check for a defective connection between the charger and battery. Ensure the power plugs are clean and undamaged. * The battery may be defective. Check the battery start. * The charger may be defective. Disconnect the charger from the mains outlet for at least 1 minute, then reconnect it. Verify that the fan starts and the green LED illuminates for about 3 seconds. If not, replace the charger.
What to do if my Husqvarna 536LiL will not start?
If your Husqvarna Trimmer isn't starting, several components could be the cause. Here's what you should check: * Inspect the battery. * Inspect the fuse. * Inspect the cables. * Inspect the safety switch. * Inspect the breaker. * Inspect the electric motor. If the issue continues after checking these, consider changing the control unit.
What to do if the Error LED flashes on my Husqvarna Trimmer?
If the Error LED is flashing, it could be due to several reasons: The power trigger and the activate button are pressed at the same time, overload, or temperature deviation. Release the power trigger and the machine will become active. For overload, remove the battery and the trimmer head from the grass. For temperature deviation, allow the machine to cool down.
What to do if Husqvarna 536LiL keypad lights flash?
If the keypad lights on your Husqvarna Trimmer are flashing, it could be due to: * A defective connection in the keypad connector. Ensure the keypad connector is correctly assembled, dry, undamaged, and free from corrosion. * A short circuit in the keypad. In this case, replace the keypad.
What does it mean when the Error LED is flashing on my Husqvarna 536LiL Trimmer battery charger?
If the Error LED is flashing on your Husqvarna Trimmer's battery charger, it means there's a temperature deviation. Use the battery charger only when the surrounding temperature is between 5 °C and 40 °C.
Why is the Error LED flashing on my Husqvarna Trimmer?
If the Error LED flashes on your Husqvarna Trimmer, it could be due to: * The power trigger and the activate button being pressed simultaneously. Release the power trigger to activate the machine. * An overload. Remove the battery and the trimmer head from the grass. * A temperature deviation. Allow the machine to cool down.
Why is the green activate LED flashing on my Husqvarna 536LiL?
If the green activate LED is flashing on your Husqvarna Trimmer, it indicates low battery voltage. Charge the battery to resolve this.
What to do if Husqvarna Trimmer product stops when applying work load?
If your Husqvarna Trimmer stops when you apply a workload, it may be due to defective power connectors. Ensure that the power connectors between the battery and the product are clean and undamaged.
What to do if Husqvarna 536LiL Trimmer warning sign flashes after start then stops?
If a warning sign on the keypad of your Husqvarna Trimmer flashes after you start it, and then the product stops, it could be due to several reasons: * The power trigger was pushed during start. Avoid pushing the power trigger when starting the product. * There is water in the main switch signal connector. Disassemble and dry the main switch connector, and then reassemble it. * There is a short circuit in the keypad. Replace the keypad. * There is a short circuit in the main switch. Replace the main switch.
General| Battery Voltage | 36 V |
|---|---|
| Cutting Width | 33 cm |
| Handle Type | Loop Handle |
| Power Source | Battery |
| Noise Level | 93 dB(A) |
| Type | Battery Trimmer |
| Blade Type | Line |
To Next Page
