Husqvarna X-COM R - User Manual

Other manuals for Husqvarna X-COM R

Workshop Manual28 pages

Questions and Answers

T
Thomas FreemanAug 15, 2025
Why won't my Husqvarna X-COM R start?
- T
  Tamara SmithAug 15, 2025
  If your Husqvarna Protection Device does not start, it could be due to several reasons. First, ensure the battery isn't out of power by charging it for at least an hour, or even a few hours if it has experienced deep discharge. Check that all cables are correctly connected using the wiring diagram, and replace any defective cables. If the battery is defective, replace it. If none of these steps work, there may be a circuit board fault, requiring you to replace the entire product.
A
Andrew AndersonAug 18, 2025
Why is there only sound from one loudspeaker on my Husqvarna X-COM R?
- A
  Abigail StevensAug 18, 2025
  If you're only getting sound from one loudspeaker on your Husqvarna Protection Device, the issue might stem from incorrect phone settings; adjust the balance settings on your phone. Also, verify that the cables are correctly connected using the wiring diagram and replace any defective cables. If the problem persists, the loudspeaker itself may be defective and need replacement. As a last resort, a defective circuit board may be the cause, in which case the product should be replaced.
D
Denise PalmerAug 21, 2025
Why is my Husqvarna X-COM R headset not charging?
- T
  Travis PatrickAug 22, 2025
  If your Husqvarna Protection Device headset doesn't charge, the problem could be a defective charger cable, which you should replace. Ensure the cables are correctly connected by using the wiring diagram and replace any that are defective. The DC connector or the battery might also be defective, requiring replacement. In some cases, a defective circuit board could be the reason, necessitating replacement of the product.
E
Emma SantanaAug 25, 2025
What to do if a function does not start when I push a button on my Husqvarna X-COM R Protection Device?
- C
  Cathy FletcherAug 25, 2025
  If a function on your Husqvarna Protection Device doesn't start when you push the button, it might be a software problem. Try a forced shutdown to reset the product, then restart and test the function again. Ensure the cables are correctly connected using the wiring diagram, replacing any defective ones. If the issue persists, the push button adapter could be defective and need replacing. In the worst case, the push button on the circuit board might be defective, requiring replacement of the product.
A
Andrew Collier DDSAug 27, 2025
Why is the sound from the boom microphone on my Husqvarna X-COM R Protection Device low or unclear?
- A
  Amber PattonAug 27, 2025
  If you're experiencing low or unclear sound from the boom microphone on your Husqvarna Protection Device, the boom microphone itself may be defective and require replacement. Check the cables are correctly connected using the wiring diagram, and replace if needed. Alternatively, the phone jack might be defective, also requiring replacement. In some cases, the circuit board may be defective, and the product should be replaced.
P
Peter StewartAug 30, 2025
Why is the sound from the microphone on my Husqvarna X-COM R Protection Device low or unclear?
- C
  Candice DukeAug 30, 2025
  If you're experiencing low or unclear sound from the microphone on your Husqvarna Protection Device, and you are in a loud work environment, try using the boom microphone accessory. If that doesn't help, the microphone itself might be defective and need replacement. Make sure the cables are connected correctly using the wiring diagram, replacing any defective ones. In some cases, a defective circuit board could be the problem, requiring headset replacement.
J
James MitchellSep 2, 2025
How to fix Bluetooth pairing issues on a Husqvarna X-COM R?
- M
  Mary RubioSep 2, 2025
  If you cannot pair your Husqvarna Protection Device via Bluetooth, first ensure the product is in pairing operation mode and retry. If issues persist, perform a forced shutdown to reset the product. Also, remove the product from the Bluetooth list on your phone and attempt pairing again. Check your phone settings and adjust if necessary before retrying. If none of these steps work, there may be a software or hardware problem, requiring replacement of the product.
J
Jamie BakerSep 5, 2025
What to do if I cannot receive phone calls on my Husqvarna Protection Device?
- S
  Samuel RhodesSep 5, 2025
  If you cannot receive phone calls on your Husqvarna Protection Device, it might be due to an incorrect configuration. Try removing the product from the Bluetooth list in your phone and retry the pairing operation. Also, change the settings on your phone and retry pairing. If the issue continues, the product may need to be replaced due to a software or hardware problem.
M
medinataraSep 8, 2025
What to do if Husqvarna X-COM R headset freezes when flashing software?
- J
  jjohnsonSep 8, 2025
  If your Husqvarna Protection Device headset freezes when you try to flash the software, it could be due to a low battery level (less than 25%) or the charger cable not being connected before flashing. Remove the battery to reset the product, then reassemble it and retry flashing the software.
T
Tamara HayesSep 12, 2025
What to do if Husqvarna X-COM R earmuffs does not respond after connection with CST?
- S
  syoungSep 12, 2025
  If your Husqvarna Protection Device earmuffs do not respond after connecting with CST, it may be because the headset is in update mode after the cable has been disconnected. Connect the power cable to the earmuffs, then connect the computer cable to both the earmuffs and the computer. Close the CST software while the earmuffs are still connected to the computer; you should hear a beep from the earmuffs.