To Next PageTo Next Page
Need help?Do you have a question about the Husqvarna YTH130 and is the answer not in the manual?
General| Engine | Briggs & Stratton |
|---|---|
| Engine Power | 13 HP |
| Cutting Height | 1.5 - 4 inches |
| Deck Material | Steel |
| Fuel Capacity | 1.5 gallons |
| Warranty | 2 years |
Learn instructions, controls, and proper use of the equipment.
Checks and actions to perform before operating the machine.
Guidelines for safe operation, including slope handling and general precautions.
Procedures for maintaining the machine and storing it safely.
Step-by-step guide to installing the steering wheel assembly.
Procedure for installing the steering wheel extension shaft.
Instructions for removing the seat from packaging and positioning it on the tractor.
Guidance on adjusting the seat for optimal operator position.
Note on battery charging if service begins after the indicated date.
Crucial safety warnings to follow before installing the battery to prevent injury.
Instructions for adjusting gauge wheels on a flat, level surface.
Procedure for setting the mower to the desired cutting height.
Identification and location of all tractor controls and their primary functions.
Operation of light switch, throttle, choke, and ignition lock for starting and running the engine.
How brake/clutch pedal, motion control lever, and gearbox operate for driving.
How to engage, disengage, lift, and lower the cutting unit using its controls.
Operation of parking brake and free-wheel control lever for tractor securing and towing.
Instructions on how to safely refuel the tractor with unleaded petrol.
Procedure for checking and maintaining the engine oil level before each use.
Guidance on checking and maintaining correct tire air pressure for optimal performance.
Steps to ensure proper engine starting, including safety switch checks.
Procedure for starting the engine when cold using the throttle and choke control.
Procedure for starting the engine when warm using the throttle control.
Procedure to remove trapped air from the transmission before operation.
Instructions on how to operate the tractor, including cutting unit engagement and motion control.
Advice on preparing the lawn by removing debris before cutting.
Guidance on adjusting cutting height for optimal results and lawn appearance.
Warning against cutting wet grass due to performance issues and potential damage.
Recommendation to clean the cutting unit after each use to maintain performance.
Safety warning regarding operating on slopes exceeding 10 degrees and risk of tipping.
Tips for turning and directing cut grass away from unwanted areas.
Steps to take before turning off the engine, including gas control and cutting unit disengagement.
Crucial safety warning regarding leaving the ignition key in the machine when not in use.
Essential safety precautions to take before performing any maintenance or repair.
Instructions for removing, reinstalling, and disconnecting the engine hood and headlight wire.
Routine checks and safety procedures to perform before operating the tractor.
Procedure for servicing the engine, including oil drain valve instructions.
Log for recording dates of completed regular service and maintenance tasks.
Importance of keeping mower blades sharp for optimal cutting performance.
Step-by-step instructions for removing mower blades for maintenance or replacement.
Guidance on sharpening mower blades for best cutting results and avoiding imbalance.
Information on the location of the brakes and procedure for adjusting brake lever distance.
Detailed steps for removing the cutting unit from the tractor.
Instructions for reassembling the cutting unit after removal.
Steps for removing and replacing the cutting unit drive belt.
Ensuring correct alignment of the cutting unit relative to the tractor's direction.
Procedure for adjusting the cutting unit's side-to-side level.
Procedure for adjusting the transaxle motion control lever to the neutral position.
Importance of keeping the transmission fan and cooling fins clean for proper operation.
Information that transaxle fluid maintenance is not required as it's factory sealed.
Common reasons and solutions when the engine fails to start or turn.
Identifying and resolving issues causing the engine to run unevenly or feel weak.
Troubleshooting steps for an engine that is overheating or lacking power.
Diagnosing and fixing problems with the battery charging or lighting system.
Troubleshooting causes for machine vibration and uneven grass cutting.
Essential steps for preparing the tractor for storage at the end of the mowing season.
Important safety warning regarding the use of gasoline for cleaning the tractor.
Information required for ordering spare parts and contacting dealers for service.
