HUST CNC H6D-T - Page 273

7 MCM Parameters
7 - 5
MCM
No.
Factory
Default
Setting
Unit Description Setting
402 10.000 mm Y-axis,Setting the value of search servo grid
403 10.000 mm Z-axis,Setting the value of search servo grid
404 10.000 mm A-axis,Setting the value of search servo grid
405 10.000 mm B-axis,Setting the value of search servo grid
406 10.000 mm C-axis,Setting the value of search servo grid
407 10.000 mm U-axis,Setting the value of search servo grid
408 10.000 mm V-axis,Setting the value of search servo grid
409 10.000 mm W-axis,Setting the value of search servo grid
410-420 0
System Reserved
421 0
X-axis Origin switch (+ :N.O (normallyopen) node; -:N.C
(normally closed) node)
422 0 Y-axis Origin switch (+ :N.O node; -:N.C node)
423 0 Z-axis Origin switch (+ :N.O node; - :N.C node)
424 0 A-axis Origin switch (+ :N.O node; - :N.C node)
425 0 B-axis Origin switch (+ :N.O node; - :N.C node)
426 0 C-axis Origin switch (+ :N.O node; - :N.C node)
427 0 U-axis Origin switch (+ :N.O node; - :N.C node)
428 0 V-axis Origin switch (+ :N.O node; - :N.C node)
429 0 W-axis Origin switch (+ :N.O node; - :N.C node)
430-440
System Reserved
441 0 X-axis, Direction of motor rotation, 0=CW, 1=CCW
442 0 Y-axis, Direction of motor rotation, 0=CW, 1=CCW
443 0 Z-axis, Direction of motor rotation, 0=CW, 1=CCW
444 0 A-axis, Direction of motor rotation, 0=CW, 1=CCW
445 0 B-axis, Direction of motor rotation, 0=CW, 1=CCW
446 0 C-axis, Direction of motor rotation, 0=CW, 1=CCW
447 0 U-axis, Direction of motor rotation, 0=CW, 1=CCW
448 0 V-axis, Direction of motor rotation, 0=CW, 1=CCW
449 0 W-axis, Direction of motor rotation, 0=CW, 1=CCW
450-460
System Reserved
461 4 X-axis,Encoder pulse multiplicationfactor,1,2,or 4
462 4 Y-axis,Encoder pulse multiplicationfactor,1,2,or 4
463 4 Z-axis,Encoder pulse multiplicationfactor,1,2,or 4
464 4 A-axis,Encoder pulse multiplicationfactor,1,2,or 4
465 4 B-axis,Encoder pulse multiplicationfactor,1,2,or 4
466 4 C-axis,Encoder pulse multiplicationfactor,1,2,or 4
467 4 U-axis,Encoder pulse multiplicationfactor,1,2,or 4
468 4 V-axis,Encoder pulse multiplicationfactor,1,2,or 4
469 4 W-axis,Encoder pulse multiplicationfactor,1,2,or 4
470-480
System Reserved
481 5 X-axis impulse command width adjustment (4=625KPPS)
482 5 Y-axis impulse command width adjustment (4=625KPPS)
483 5 Z-axis impulse command width adjustment (4=625KPPS)
484 5 A-axis impulse command width adjustment (4=625KPPS)
485 5 B-axis impulse command width adjustment (4=625KPPS)
486 5 C-axis impulse command width adjustment (4=625KPPS)
487 5 U-axis impulse command width adjustment (4=625KPPS)
488 5 V-axis impulse command width adjustment (4=625KPPS)
489 5 W-axis impulse command width adjustment (4=625KPPS)
490-500 6
System Reserved
501 0
Master/Slave mode, 0=CNC, 1=X-axis, 2=Y-axis
3=Z-axis,4=A-axis,5=B-axis,6=C-axis,7=U-axis,