The Hybrid HMH 7 is a lighting fixture designed for various applications such as discotheques, clubs, bars, parties, and mobile DJs. It offers versatile control options including DMX, Master/Slave, Sound Active, and Auto modes, along with dimmer functionality.
Function Description:
The Hybrid HMH 7 is a high-power LED lighting fixture featuring seven 10W Quad-color LEDs. Each of the Red, Green, Blue, and White colors can be controlled individually, allowing for a wide range of color mixing and effects. It supports both 5-channel and 13-channel DMX modes, providing flexibility in control. The unit offers smooth 0-100% dimming and variable strobe speeds, enabling dynamic lighting effects. In Master/Slave mode, multiple units can be linked to create synchronized light shows, which can be sound-activated or automatic.
Important Technical Specifications:
- LEDs: 7 x 10W Quad-color LEDs with a rated lifespan of 60,000 hours.
- Input Voltage: 220-240 Vac / 50-60 Hz.
- Power Consumption: 70W.
- Beam Angle: 45°.
- Fuse: T 3A.
- Dimensions: 177 x 177 x 240 mm.
- Weight: 2.8kg.
- DMX Channels: Switchable between 5 and 13 channels.
- Operation Modes: DMX, Master/Slave, Sound Active, Auto, Dimmer.
- Ambient Temperature: Maximum Ta: 40℃.
Usage Features:
The device can be operated in three main ways:
- Master/Slave Built-In Preprogrammed Function: This allows for an instant, synchronized light show. To use this, the first unit (master) should be set to Automatic or Sound Activated mode, with nothing plugged into its DMX input jack. Subsequent units (slaves) should be set to address A001, with their DMX input jacks connected in a daisy chain. The slave LED lights will remain constantly on in this mode.
- DMX Controller: The Hybrid HMH 7 is DMX512 compatible, allowing for precise control over its functions. It can be connected in a daisy chain using XLR plug cables. The DMX address can be set between 0-511.
- 5-Channel Mode:
- CH1: PAN (0-255)
- CH2: TILT (0-255)
- CH3: PAN/TILT speed from fast to slow (0-255)
- CH4: Strobe speed from slow to fast (0-255)
- CH5: To select 255 kinds of color (0-255)
- 13-Channel Mode:
- CH1: PAN (0-255)
- CH2: PAN Fine (0-255)
- CH3: TILT (0-255)
- CH4: TILT Fine (0-255)
- CH5: PAN/TILT speed from fast to slow (0-255)
- CH6: Strobe speed from slow to fast (0-255)
- CH7: Red dimmer (0-255)
- CH8: Green dimmer (0-255)
- CH9: Blue dimmer (0-255)
- CH10: White dimmer (0-255)
- CH11: CH7~CH10 effectivity (0) / To select 255 kinds of color (1-255)
- CH12: Custom control by DMX512 (0) / Slow running (1-84) / Fast running (85-169) / Sound mode (170-255)
- CH13: Reset (255)
- Rear Panel Controls: The unit features a control panel with a display and four buttons (MODE/ESC, UP, DOWN, ENTER) for navigating menus and selecting functions.
- MENU: Selects programming functions.
- UP: Moves forward in selected functions.
- DOWN: Moves backward in selected functions.
- ENTER: Enters submenus.
- Mains input: Connects to the power supply.
- DMX input/output: Uses 3/5-pin XLR plug cables for DMX signal input and linking to subsequent units.
Installation:
The unit should be securely mounted via its screw holes on the bracket to prevent vibration and slipping. The mounting structure must be able to support at least 10 times the unit's weight, and a safety cable capable of holding 12 times the unit's weight should always be used. Installation should be performed by professionals in a location out of reach of people.
Safety Instructions:
- Always ground the yellow/green conductor to earth to prevent electric shock.
- Disconnect main power before servicing or maintenance.
- Do not operate the fixture above 40℃ ambient temperature.
- In case of serious operating problems, stop use immediately and contact an authorized technical assistance center; do not attempt repairs yourself.
- Use only the same type of spare parts.
- Do not connect to any dimmer pack.
- Avoid touching wires during operation due to electric shock hazard.
- Do not expose the fixture to rain or moisture.
- Replace visibly damaged housing.
- Do not look directly at the LED light beam.
- Keep the magnifying lens out of direct sunlight to prevent heat buildup and damage.
Maintenance Features:
Regular cleaning is essential to optimize light output.
- External Optics: Clean at least every 20 days with a soft cloth and normal glass cleaning fluid.
- Internal Optics: Clean at least every 30-60 days.
- Always dry parts carefully after cleaning.
- Cleaning frequency depends on the operating environment (damp, smoky, or dirty conditions require more frequent cleaning).
- There are no user-serviceable parts inside; do not open the housing or attempt repairs. Contact a dealer for service.
Need help?
General
To Next Page
