Hyundai HYCH707-2 - User Manual

Questions and Answers

C
chad04Aug 18, 2025
Why is my Hyundai HYCH707-2 shredder not shredding properly?
- M
  Mario BrewerAug 18, 2025
  To address the issue of the shredder not shredding properly, which results in wood not being pulled into the machine and inconsistent chip sizes, you should first inspect the blades for wear and either sharpen or replace them, noting they can be reversed due to being sharpened on both edges. Ensure that the branches you're inserting are not exceeding the recommended diameter (100 mm for HYCH1500E-2 or 70mm for HYCH7070[E]-2). Also, verify that the gap between the fixed blade and the counter-blade is correctly set to ½ mm, adjusting it in the slots if necessary.
C
Cindy BarrettAug 21, 2025
What to do if Hyundai HYCH707-2 has starting difficulty with normal spark and fuel issue?
- J
  joyjonesAug 21, 2025
  If you're experiencing starting difficulties with your Hyundai Chipper and observe a normal spark with fuel system, begin by checking the fuel supply. Ensure there is fuel in the system and that the fuel tap is open. Clear any blockage from the fuel cap air vent or the fuel tap itself. If the fuel supply is normal, consider that dirty or stale fuel, water contamination, or incorrect fuel type could be the cause. In such cases, clear the fuel from the system and refill with fresh fuel.
T
Tina GriffithAug 23, 2025
How to troubleshoot Hyundai HYCH707-2 Chipper engine that will not start?
- D
  donald72Aug 23, 2025
  If your Hyundai Chipper engine won't start, consult the engine user manual. Check the fuel level and make sure the fuel is fresh. Verify that the ON-OFF switch is in the ON position, check the lubrication oil level, and ensure the emergency stop button is not engaged.
J
Joseph HolmesAug 26, 2025
What to do if Hyundai HYCH707-2 (electric) has starting difficulty?
- K
  Kevin HolmesAug 26, 2025
  If you face starting difficulty with your Hyundai Chipper (electric model), check the battery connections to ensure they are tight and have the correct polarity. If connections are secure, remove the battery from the machine and recharge it, as the battery may not be charged.
F
fcobbAug 28, 2025
Why Hyundai HYCH707-2 has starting difficulty normal fuel issue HT lead/spark plug?
- C
  Charles SchmittAug 28, 2025
  If you are experiencing starting difficulties with your Hyundai Chipper, and there's a normal fuel issue but problems with the HT lead/spark plug, you can try the following: Clean any carbon buildup from the spark plug, or replace the spark plug if the electrodes are badly burnt or damaged. Adjust the spark plug gap. If there's no spark at the HT lead, replace the HT lead or the ignition coil. Also, adjust the gap between the ignition coil and flywheel.
J
jessica02Aug 30, 2025
What to do if Hyundai Chipper engine cuts out during operation?
- D
  danielbakerAug 30, 2025
  If the engine of your Hyundai Chipper cuts out during operation, first check if the engine stopped due to overloading. Then, check if the discharge chute is clear and that the rotary blade is not jammed. Finally, check the emergency stop lever and safety protection switch.
J
Jennifer CarterSep 1, 2025
Why Hyundai Chipper engine will not start because the rotor is jammed?
- C
  Catherine Johnson DDSSep 1, 2025
  If the engine of your Hyundai Chipper will not start or turn because the rotor is jammed, shut off the engine and remove the spark plug cap. Never use your hands to remove stuck wood. Reduce the size of wood to 100 mm for HYCH1500E-2 or 70mm for HY- CH7070[E]-2 or less. Use a piece of wood to turn the rotor to remove the material from the rotor and input tube. If necessary, remove the cap of the bearing housing and rotate the rotor axle with a spanner. If necessary, remove the input or output tube to get access to the rotor. Check the sharpness of all blades, have them sharpened or replace as required. Make sure all blade bolts are properly tightened.
J
Jennifer HaasSep 3, 2025
What to do if Hyundai HYCH707-2 Chipper hopper is blocked?
- E
  Emily Whitehead DDSSep 4, 2025
  If your Hyundai Chipper's hopper is blocked, stop the machine. Remove the hoppers and clear the blocked material. Be careful not to touch the blade during this process.
U
usmithSep 6, 2025
Why is my Hyundai HYCH707-2 Chipper making unusual noises?
- R
  Robert WatsonSep 6, 2025
  If your Hyundai Chipper is making unusual noises, stop the machine. Check that all nuts and bolts are tight. Inspect the bearings for excessive play, and ensure that blades and belts are not rubbing anywhere.
B
Becky WrightSep 8, 2025
What causes belts slipping on Hyundai HYCH707-2 Chipper?
- A
  Andrew WillisSep 8, 2025
  If you notice belts slipping on your Hyundai Chipper, make sure the belt tensioner is adjusted correctly. If the problem persists, consider fitting new belts.