Why is my HYVA Construction Equipment vibrating and jerking during initial maneuvers?
If you're experiencing vibrations in the crane cylinders and the boom extension cylinders jerk during the initial maneuvers of your HYVA Construction Equipment, the hydraulic oil temperature may be too low. Perform maneuvers without load for several minutes in order to warm up the oil.
Why is rotation blocked in one direction on my HYVA Construction Equipment?
If rotation is blocked in one direction on your HYVA Construction Equipment, it may be that the slewing limiting device triggered.
Why are the control levers blocked in one direction in HYVA AMCO VEBA 911-3S Construction Equipment?
If the control levers of the 1. boom and hydraulic extensions cylinders are blocked in one direction on your HYVA Construction Equipment, it may be because the load limiting device is on.
How to stop squeaking on HYVA AMCO VEBA 911-3S articulation points?
If you notice squeaking on the articulation points or slewing unit bushing of your HYVA Construction Equipment, it is likely due to a lack of lubrication. Grease the articulation points or bushings to resolve this.
Why does the HYVA Construction Equipment stabilizer leg close during crane work?
If the stabilizer leg closes during the crane work with your HYVA Construction Equipment, it could be due to the block valve on the stabilizer leg worn, no more seal. Go to an authorized assistance center. Another potential cause is internal seals wear. Go to an authorized assistance center.
What does it mean if I find metal particles in HYVA Construction Equipment oil filters?
If metal particles are found in the oil filters of your HYVA Construction Equipment, some parts of the hydraulic circuit may be in a state of deterioration. Go to an authorized assistance center.
What to do if HYVA Construction Equipment crane is blocked with a load?
If the HYVA Construction Equipment crane with the load at the hook is blocked but the permitted movements are different from the ones set out in ยง0, it could be due to anomalies in the system monitoring the position of the booms or anomalies of the load limiting device. Exclude the load limiting device and, solely in order to deposit the load on the ground and thus set the crane in its rest configuration, perform the manoeuvres required to maintain or reduce the distance of the load from the column axis.
What to do if HYVA AMCO VEBA 911-3S load limiting device operates beyond tolerance?
If the load limiting device comes into operation beyond its tolerance limits on your HYVA Construction Equipment, this may be due to incorrect setting of the load limiting device. Go to an authorized assistance center.
Why HYVA AMCO VEBA 911-3S crane fails to lift the required load?
If the HYVA Construction Equipment crane fails to lift the required load with all movements, it may be due to general overpressure valve worn, no more seal or dirty. Go to an authorized assistance center. Another possible cause is oil leakage at some part of the circuit. Go to an authorized assistance center.
What to do if HYVA Construction Equipment crane control levers produce no movement?
If operating the control levers produces no movement of the HYVA Construction Equipment crane, check the following: * Ensure there is motive power. * Verify the switch key is inserted and the green light is on. * Disengage the emergency push-button after checking there are no dangerous conditions.
Details hazards related to mechanical aspects of the crane, including temperature, incline, and wind.
Explains how environmental factors affect crane structural integrity and material properties.
Warns about risks of being crushed by moving crane components.
Details residual hazards related to arm movement and connecting rods, causing cutting injuries.
Describes hazards from failure to maintain safety distances in the crane operating area.
Identifies hazards from impacts with crane components, loads, or stabilizers.
Warns about serious damage from instability; emphasizes correct stabilization.
Covers risks from contact with live components or lightning strikes.
Explains risks from crane contact with power lines or lightning strikes.
Details hazards related to high temperatures, including burns and environmental heat.
Covers hazards from exhaust fumes, toxic substances, and improper fluid handling.
Addresses hazards related to operating positions, visibility, and human error.
Identifies hazards from incorrect crane operation, maintenance, or stabilization.
Details risks of impact, crushing, and load/stability loss from accidental crane start-up/shutdown.
Explains risks from tampering with safety devices and the importance of warning decals.
Highlights risks of damage and injury from incorrect component coupling.
Lists hazards from incorrect load handling, including stability loss and uncontrolled movements.
Provides safety instructions for safely moving and transporting the crane.
Details specific hazards related to remote control operation, including interference and errors.
Lists additional specific hazards for cranes mounting a winch.
Highlights specific hazards when cranes are fitted with bucket or grab attachments.
Details specific hazards for cranes mounting a drill attachment.
Provides manufacturer, crane type, lifting components, classification, and operating life.
Outlines assembly, operator training, and required customer documentation.
Specifies environmental and operational conditions for safe machine operation.
Details safety devices, limiters, and indicators fitted to the crane for safe operation.
Details the function of various controls and indicators on the crane's control panels.
Details the function of various safety devices, limiters, and indicators on the crane.
Explains the function and operation of emergency stop buttons for immediate blocking of crane movements.
Details pre-operation checks, focusing on climatic and atmospheric conditions.
Specifies the minimum safe distance from electricity power lines.
Provides instructions for starting and operating the crane safely.
Step-by-step instructions for stabilizing the crane, including manual extension and wheel block.
Lists essential checks before leaving the work site, ensuring crane safety and shutdown.
Lists routine maintenance operations for machine efficiency.
Illustrates load capacities for the 810 model, considering winch variations.
Presents load capacities for the 810C model, considering winch type and tool weight.
Illustrates load capacities for the 911 model, considering winch variations.
Presents load capacities for the 911C model, considering winch type and tool weight.
Lists possible causes for malfunctions and corrective actions.
General| Brand | HYVA |
|---|---|
| Model | AMCO VEBA 911-3S |
| Category | Construction Equipment |
| Language | English |
To Next Page
