IBM Europe, Middle East, and Africa
Hardware Announcement ZG09-0169
IBM is a registered trademark of International Business Machines Corporation
24
• The rack must include perforated front and rear doors and must not prevent the
flow of cool air into or out of the rack.
• The weight-handling capacity of the rack must be able to support the maximum
rack configuration, including all servers, external cables, and PDUs.
• The rack must provide proper stabilization so that the rack does not become
unstable when servers are pulled out for service.
Processor upgrade options
• Dual-Core Intel Xeon Processor E5502 1.86GHz/4MB DDR3 800MHz/4.8GT/S 80W
No Turbo - 46M1077
• Quad-Core Intel Xeon Processor E5504 2.00GHz/4MB DDR3 800MHz/4.8GT/S 80W
No Turbo - 46M1078
• Quad-Core Intel Xeon Processor E5506 2.13GHz/4MB DDR3 800MHz/4.8GT/S 80W
No Turbo - 46M1079
• Quad-Core Intel Xeon Processor L5520 2.26GHz/8MB DDR3 1066MHz/5.8GT/S
80W No Turbo - 46M1080
• Quad-Core Intel Xeon Processor E5520 2.26GHz/8MB DDR3 1066MHz/5.8GT/S
80W Turbo - 46M1081
• Quad-Core Intel Xeon Processor L5506 2.13GHz/4MB DDR3 800MHz/4.8GT/S 80W
Turbo - 46M1082
• Quad-Core Intel Xeon Processor E5530 2.40GHz/8MB DDR3 1066MHz/5.8GT/S
80W Turbo - 46M1083
• Quad-Core Intel Xeon Processor E5540 2.53GHz/8MB DDR3 1066MHz/5.8GT/S
80W Turbo - 46M1084
• Quad-Core Intel Xeon Processor X5550 2.66GHz/8MB DDR3 1333MHz/6.4GT/S
95W Turbo - 46M1085
• Quad-Core Intel Xeon Processor X5560 2.80GHz/8MB DDR3 1333MHz/6.4GT/S
95W Turbo - 46M1086
• Quad-Core Intel Xeon Processor X5570 2.93GHz/8MB DDR3 1333MHz/6.4GT/S
95W Turbo - 46M1087
Supported memory options
The following memory options are supported:
• 44T1480 - 1GB (1x1GB) Single Rank
• 44T1481 - 2GB (1x2GB) Dual Rank
• 44T1482 - 2GB (1x2GB) Single Rank
• 44T1483 - 4GB (1x4GB) Dual Rank
Power considerations
The System x3650 M2 server includes a standard 675-watt hot-swap power supply.
This power supply supplies sufficient power to run the server. A System x3650
M2 675-watt hot-swap power supply upgrade is optionally available to support
redundancy.
Cable orders
Two 10/100/1000 Mbps, full-duplex Ethernet PCI controllers, standard with the
System x3650 M2 server, are connected directly to an independent RJ-45 connector.
The RJ-45 connector provides a 10BaseT, 100Base-TX, and 1000Base-TX interface
for connecting twisted-pair cable to the Ethernet network. Cabling is not included
with the server. To connect the Ethernet controller to a repeater or switch, use
an unshielded twisted pair (UTP) cable with RJ-45 connectors at both ends. For
100/1000 Mbps operation, Category 5 cabling must be used. For 10 Mbps operation,
Category 3, or better, cabling must be used.
There are no additional cabling requirements, other than for system power,
keyboard, mouse, and monitor connections.
To Next Page
Loading...
Need help?
General
