IceTech SP 25 - User Manual

Questions and Answers

C
Charles TrevinoAug 21, 2025
How to fix IceTech SP 25 when none of the electrics work?
- E
  Edward MillerAug 21, 2025
  If none of the electrics are working on your IceTech Ice Maker, start by ensuring the machine is properly plugged in. If it is, check the line fuse and replace it if it has blown. Also, inspect the current line connections in the junction box to ensure they are correctly connected. Furthermore, the cut-off micro-switch might be faulty or incorrectly adjusted, so check, adjust, or replace it as necessary. Finally, a faulty safety pressostat could also be the cause, so consider replacing it.
M
Mike MccarthyAug 26, 2025
Why does my IceTech Ice Maker compressor cycle intermittently?
- B
  brianmercerAug 26, 2025
  If all the electrics work but the compressor cycles intermittently on your IceTech Ice Maker, start by checking the voltage to ensure it's not too low. A dirty condenser can also cause this issue, so clean it. Make sure there's no obstruction in air circulation around the machine; move it to a correct position if needed. Other potential causes include a broken fan (replace it), a faulty starter capacitor (replace the condenser), a faulty or wrongly adjusted fan presostat (replace or adjust it), a faulty or wrongly adjusted water presostat valve (replace or adjust it), a faulty or badly adjusted cooling water pressostat (adjust or change it), a faulty cooling water entry valve (change it), or non-condensable gases in the system (purge the system).
K
Kayla RossAug 27, 2025
What if all electrics work except compressor in IceTech SP 25 Ice Maker?
- J
  James AllenAug 28, 2025
  If all the electrics work on your IceTech Ice Maker, except for the compressor, there are a few things you can check. Start by looking for any loose wires and check the connections. If the wiring is secure, the relay may be faulty, in which case you should replace it. Another possibility is a faulty 'Klixon,' which would also need to be replaced. If neither of those solutions works, the compressor itself may be faulty and require replacement.
X
Xavier WagnerAug 30, 2025
Why does IceTech SP 25 produce ice slabs?
- L
  Laura ThompsonAug 30, 2025
  If your IceTech Ice Maker is producing ice slabs, especially in very low ambient and water temperatures, it could be due to several reasons. The cycle thermostat might be set too low or be faulty, so adjust or change it. Another possibility is that the timer wheels aren't turning, so tighten the screws on the timer. If the timer motor is faulty, check and replace it. Lastly, the micros on the timer could be faulty, so replace them and check for bridging.
G
Gregory DaviesSep 1, 2025
How to increase ice production in IceTech SP 25 Ice Maker?
- K
  katherinevargasSep 1, 2025
  To increase ice production in your IceTech Ice Maker, start by cleaning the condenser and improving air circulation around the machine. For water-cooled machines, ensure the condenser is clean and that the valve and pressostat are properly adjusted. If these steps don't help, you may need to replace certain components. Specifically, check the fan and readjust the pressostat or replace it if necessary. Also, inspect the water inlet valve for leaks and replace if needed. Finally, ensure that the refrigerant charge is at the correct level, adjusting if necessary.
B
bridget30Sep 3, 2025
Why are IceTech SP 25 cubes too small and empty?
- R
  rebecca13Sep 4, 2025
  If your IceTech Ice Maker is producing ice cubes that are too small and empty, especially in high ambient and water temperatures, it's likely that the cycle thermostat is adjusted too low, so adjust it until you achieve the desired cube size. Another potential cause is a low refrigerant charge, so add refrigerant until there is frost formation 5 cm from the compressor at the end of the cycle.
T
Tiffany ThompsonSep 6, 2025
How to adjust IceTech SP 25 Ice Maker for smaller ice cubes?
- D
  Danielle SmithSep 6, 2025
  If your IceTech Ice Maker is producing ice cubes that are too large, especially in low ambient and water temperatures, the cycle thermostat is likely adjusted too high. Adjust it until you achieve the desired cube size.
C
Cory SolisSep 8, 2025
Why are ice cubes from my IceTech Ice Maker empty and white?
- M
  Melissa OwensSep 8, 2025
  If the ice cubes from your IceTech Ice Maker are empty, have rough edges, and appear very white, it could be due to several reasons. There might be insufficient water in the water pan due to an unprimed pump, so correct any major water leaks. Obstructed spray nozzles can also cause this, so clean them. If the curtain doesn't close fully, adjust it and clean any scale (lime) on the curtain's metal axis. For DP 90 and 140 models only, the buoy and valve mechanism might be obstructed, so check, clean, and replace if necessary.
T
Timothy VanceSep 12, 2025
What causes ice cubes to stick in IceTech SP 25?
- L
  Laura BarnettSep 12, 2025
  If your IceTech Ice Maker forms ice cubes correctly but they don't unstick, it's likely due to dirty water inlet filters. You should clean the filters on both ends of the water hose connected to the mains.
C
Curtis JonesSep 13, 2025
What to do if IceTech SP 25 Ice Maker doesn’t stop when bin is full?
- M
  Mathew HillSep 13, 2025
  If your IceTech Ice Maker doesn’t stop even when the bin is full, it indicates a faulty or badly adjusted bin thermostat. Adjust it, and if that doesn't resolve the issue, replace it.