Icron USB 2.0 Ranger Series

Questions and Answers

J
Jason ChavezJul 28, 2025
Why are all the LEDs off on my Icron USB 2.0 Ranger's LEX and REX units?
- K
  Kim JohnsonJul 28, 2025
  If all LEDs on both the LEX unit and REX unit of your Icron Adapter are off, it means the USB 2.0 Ranger is not receiving power. To resolve this: * Ensure that the power adapters are correctly connected to both the LEX and REX units. * Verify that these adapters are connected to a working electrical power source.
G
gregory75Aug 14, 2025
How to fix Link LEDs off on Icron Adapter LEX and REX units?
- S
  steven26Aug 15, 2025
  If the Link LEDs on both the LEX and REX units of your Icron Adapter are off, it indicates there is no connection between the LEX unit and the REX unit. To fix this: * Ensure a Category 5 UTP cable with straight-through conductors is properly connected between the LEX unit and the REX unit. * Try connecting a short Category 5 patch cord between the LEX unit and the REX unit to test the system.
S
shawngeorgeAug 20, 2025
Why is the Host LED off on my Icron Adapter LEX unit when the Link LED is on?
- A
  afisherAug 20, 2025
  If the Link LED is on, but the Host LED is off on the LEX unit of your Icron Adapter, the possible causes are: * The computer is not functioning. * The LEX unit is not properly connected to the computer. * The computer does not support USB 2.0 hubs. * The USB 2.0 Ranger is malfunctioning. Try the following steps to resolve the issue: 1. Disconnect all USB devices from the REX unit. 2. Disconnect the LEX unit from the computer. 3. Disconnect and then reconnect the power adapters to the USB 2.0 Ranger. 4. Reconnect the LEX unit to the computer. 5. Check in the Universal Serial Bus controllers section of Device Manager that the USB 2.0 Ranger is recognized as a “Generic USB Hub”. 6. If it is not recognized, contact Icron technical support for assistance.
K
Karen HernandezNov 2, 2025
What to do if the Device LED is off when a device is connected to the Icron Adapter's REX unit?
- R
  Reginald SpencerNov 2, 2025
  If a device connected to the REX unit of your Icron Adapter has its corresponding Device LED off, it could be due to several reasons: * The USB device itself might be malfunctioning. * The computer may not be recognizing the USB device. * The application software required for the device might not be running correctly. * The USB 2.0 Ranger could be malfunctioning. Here's what you can do to troubleshoot: 1. Disconnect the USB 2.0 Ranger from the computer. 2. Connect the USB device directly to the computer's USB port. 3. If the device still doesn't work, refer to its user manual. 4. If it works when connected directly to the computer, try connecting another device to the USB 2.0 Ranger and then connect the Ranger to the computer. 5. If the second device doesn't work, the USB 2...
L
lorideanNov 8, 2025
What to do if all LEDs are on, but the device connected to my Icron Adapter doesn't operate correctly?
- S
  sanchezannaNov 8, 2025
  If all LEDs on the LEX and REX units of your Icron Adapter are lit, but the connected device isn't working correctly, consider these possibilities: * The USB device may be malfunctioning. * The computer might not recognize the USB device. * The device's application software might not be running. * The USB 2.0 Ranger itself could be malfunctioning. Try these troubleshooting steps: 1. Disconnect the USB 2.0 Ranger from the computer. 2. Connect the USB device directly to a USB port on the computer. 3. If the device fails to operate, check its user documentation. 4. If it operates correctly when directly connected, connect a different device to the USB 2.0 Ranger and then connect the Ranger to the computer. 5. If the second device doesn't work, the USB 2.0 Ranger might be defec...