ICS 680GC User Manual (English)

Other manuals for ICS 680GC

Operator's Manual27 pages

Quick Start Guide2 pages

Questions and Answers:

C
Cindy CastilloAug 16, 2025
What to do if my ICS 680GC Chainsaw will not start?
- N
  Nathan TaylorAug 17, 2025
  If your ICS Chainsaw won't start, there are several potential causes. First, clean, rebuild, or replace the recoil starter if it's dirty or broken. If the spark plug is soaked with fuel, dry it and expel excess fuel from the cylinder and crankcase. Ensure the switch is in the 'ON' position. Check and tighten ground wire connections, or replace the ground wire if necessary. Repair or replace the spark plug lead. Consider replacing the ignition coil. If the issue persists, it may be due to internal damage, requiring replacement of the piston and cylinder. Ensure you are using the correct fuel/oil mixture (25:1) and fresh fuel.
L
Luke KnoxAug 19, 2025
How to fix ICS 680GC Chainsaw engine running rough?
- A
  Adam BrownAug 20, 2025
  If your ICS Chainsaw engine runs rough at all speeds, it could be due to a dirty or clogged air filter. Try cleaning or replacing the air filter. It may also be caused by water ingestion or a loose or dirty spark plug.
D
darrylpearsonAug 22, 2025
Why is my ICS 680GC Chainsaw engine overheating?
- B
  bryan36Aug 22, 2025
  The engine of your ICS Chainsaw could be overheating if the operator is overworking the saw, the carburetor mixture is too lean, the fuel/oil ratio is incorrect, the flywheel fins are clogged, the air deflector is missing, or the cylinder fins are clogged. Clean or replace the air filter. You may also need to replace the fuel filter, refer to the Carburetor Tuning section, repair or replace the fuel tank breather, or replace the pulse tube.
C
Charlotte LucasAug 26, 2025
What causes poor acceleration in ICS 680GC Chainsaw?
- H
  Haley EllisonAug 26, 2025
  Poor acceleration in your ICS Chainsaw can be caused by a dirty or clogged air filter, a clogged fuel filter, an incorrect carburetor tune, a plugged tank breather, or a blocked pulse tube.
H
Heather CarpenterAug 28, 2025
What causes uneven idle in ICS Chainsaw?
- K
  katherinecollinsAug 28, 2025
  Uneven idle or 'run away' engine in your ICS Chainsaw can be caused by an air leak at the intake boot, cylinder gasket, or crankcase gasket, or a faulty carburetor diaphragm.
C
Christopher MurphyAug 30, 2025
Why does diamond chain move at idle on my ICS Chainsaw?
- W
  wallerpatriciaAug 30, 2025
  If the diamond chain moves at idle on your ICS Chainsaw, this can be due to the idle speed being too high or a broken clutch spring.
J
Joshua PerrySep 2, 2025
What to do if my ICS Chainsaw is difficult to start?
- K
  Kimberly BakerSep 2, 2025
  If your ICS Chainsaw is difficult to start, it might be due to a flooded engine. To resolve this, turn the ignition switch on, push the choke in, hold the throttle on full with your foot, and pull the starter cord in rapid succession until the engine starts. Another cause might be a fouled spark plug. In this case, remove the spark plug, clean it, and regap it to .020 in (.05 mm).
A
Alec GallagherSep 4, 2025
Why my ICS 680GC won't reach full RPM?
- E
  Erika VincentSep 5, 2025
  There are a few potential reasons why your ICS Chainsaw won't reach full RPM. It could be due to a dirty air filter or pre-filter. Another possibility is that the chain tension is too tight. The diamond chain should always be able to be pulled around the guidebar by hand, and it is normal for the diamond chain links to hang below the guidebar.
S
Sharon WilliamsSep 7, 2025
Why is the diamond chain speed slow on my ICS 680GC?
- J
  Jeffrey MoraSep 7, 2025
  If your ICS Chainsaw's diamond chain speed is slow, the diamonds may be glazed over. To fix this, make a few cuts in an abrasive material to expose the diamonds.