IgniteNet Spark SP-W2M-AC1200 User Manual

– 1 –
Quick Start Guide
1. Unpack the AP
◆
Spark AC Wave2 Mini, SP-W2M-AC1200
◆
Universal AC/DC power adapter
◆
USB cable — Micro to Type A
◆
Cat 5e Ethernet cable, 1.2 m (4 ft)
◆
2 Med Command strips
◆
Quick Start Guide (this document)
2. Mount the AP
a. Mounting the AP on a Wall
At the installation location on the wall, mark two holes
44 mm (1.73 in) apart for the wall plugs and screws (not
included).
Drill two holes for the wall plugs, and then insert the plugs
and tap them flush with the wall surface.
Insert the two screws in the wall plugs leaving the screw
heads about 5 mm from the wall surface.
With its ports facing down, place the AP’s mounting points
over the two screws, and then slide it down on the screws.
Do not let go of the AP until you confirm that it is secure.
b. Alternative Wall-Mounting Method
Position and stick the two supplied Med Command strips to
the base of the AP as shown.
Position the AP on the wall and press firmly for 30 seconds.
Remove the AP from the wall to separate the strips. Wait a
further hour before mounting the AP.
Mount the AP by pressing the strips together until they click.
1
2
2
1
1
2
1
1
1
c. Mounting the AP on a Desktop
Attach the included four rubber feet to the base of the AP.
Place the AP on the desktop.
3. Connect Cables
Connect the cable from the AC/DC power adapter to the USB
power jack on the AP.
Connect the power adapter to a nearby AC power source
(100-240 VAC, 50/60 Hz).
Connect Category 5e or better cable to the 1000BASE-T
Eth1 RJ-45 port.
Connect the other end of this cable to a LAN switch.
(Optional) Connect a local LAN device to the Eth2 RJ-45 port
on the AP using Category 5e or better cable.
This Eth2 RJ-45 port is a 100BASE-TX port.
4. Verify AP Operation
The power LED should be on green.
1
1
1
1
1
3
1
2
1
2
3
1
2
3
1
Spark SP-W2M-AC1200
E122017-CS 150200001xxxX R01
Cloud-Enabled Indoor Access Point
Spark™ AC Wave2 Mini, SP-W2M-AC1200
ignitenet.com

IgniteNet Spark SP-W2M-AC1200 Specifications

General

Model	SP-W2M-AC1200
Wireless Standard	802.11ac
Frequency Bands	2.4 GHz, 5 GHz
Maximum Data Rate	1200 Mbps
Ethernet Ports	1x 10/100/1000 Mbps
Mounting Options	Wall, Ceiling
Power over Ethernet (PoE)	Yes
Power Method	PoE, DC

Summary

Mount the AP

Mounting the AP on a Wall

Provides step-by-step instructions for wall mounting the AP using screws.

Alternative Wall-Mounting Method

Details using adhesive strips for an alternative AP wall mounting method.

Mounting the AP on a Desktop

Explains how to attach rubber feet and place the AP on a desktop.

Connect Cables

Verify AP Operation

Connect to the Web User Interface

Complete the Setup Wizard

Manage the AP with the IgniteNet Cloud Controller

Process for registering the AP with the IgniteNet Cloud Controller.

Manage the AP in Stand-Alone Mode

Guidance on manual configuration via the web interface.

Safety and Regulatory Information (FCC & Industry Canada)

Regional Compliance and Warnings

EU and Japan Regulatory Statements

Covers EU Declaration of Conformity, Japan, and Taiwan (NCC) statements.

Warnings and Cautionary Messages

Important warnings and cautions for safe installation and operation.

Hardware Specifications

Chassis and Environmental Specs

Details physical dimensions, weight, operating temperature, and humidity.

Network Interface Details

Information on Ethernet ports and Wi-Fi radio standards.

Power Supply and Consumption

Specifies power adapter requirements and typical power usage.

Regulatory Compliances and Certifications

Lists relevant radio and emissions compliance standards.

Manufacturer Information

Identifies the manufacturer and their location.