@IHUEIPRESET Switch
This switch adjusts the preset hue value . When
operatin g in P AL-B, this switch does not work unless
the front panellS-PAL jswitch is
"ON" (and its LED is
lit up). The operation procedure is the same
as for®.
For details of the adjustment method, see 5-4.(2).
@ICHROMAIPRESET Switch
This switch adjusts the preset chroma value. The
operat ion procedure is the same
as for ®· For deta ils
of the adjustment method , see 5-4. (2).
Sett ing of YPnPa CHROMA PRESET Data
· Since the CHROMA PRESET data setting can be
made exclusively for
YPnPR separat ely from the
norm al CHROMA dat a setting, it allows com-
patib ility with various sorts of VTR stand ards.
The exclusive CHROMA data for
YPaPn of
MODE 1 to MODE 3
can be stored into FILE 1
to FILE 3 similarly to the normal CHROMA data.
· By setting the "YPbPr MODE" of MENU Item 3
(See 5-6(5)), chroma data of various typ es of
standards can be outp ut.
"MODEl"
"MODE 2"
"MODE
3"
SMPTE · MH · NlO
(Factory setting values)
BETA (Factory sett ing values)
USER (Exclusive user data)
In MODEl, and MODE2, the chroma preset data
corresponding to the signal input level described
in 3-3(1) is memorized.
@ IBRIGHTIPRESET Switch
This switch adjusts the preset brightness value. This
switch does not work in delay stat e. Also, if this
IBRIGHTI preset switch is
"ON" (and its LED lit up),
if you switch int o delay state , this switch is
automa tic ally switched off
(and its LED goes out).
The operation procedure is the same as for
®· For
details on the adjustment method, see 5-4.(5).
@I CONTIPRESET Switch
This switch adjusts the preset contrast value. The
operation procedure is the same
as for ®· For details
on the adjustment method, see 5-4.(6).
@ !STORE FILE!Switch
This switch stor es the data for Files 1-3. When you
press this switch, IFILEll- IFILE31 blink. Pressing the
key for the file into which you want to store the data,
the FILE selected lights up and the data is stored into
it. For details on the operation procedure, see
Examp le 1 and Example 2 in 5-5.(2) .
@!FILE l lSwitch
To output the data stored in Filel( preset data®-@)
or to store data into File 1, switch th is switch "ON".
F or
details on the operation procedure , see Example 1
and Example 2 in 5-5.(2).
@ !FILE 2jSwitch
Same as switch @.
@IFILE 31 Switch
Same as switch ®·
@!MENU! Switch
This switch calls out the various menus . For details,
see 5-6.
® IENTISwitch
This switch is for menu operation. For deta ils, see 5-6.
@IESCI Switch
This switch is for menu operat ion. For details, see 5-6.
@IU. DISPLAY!Switch
This switch displays the titles for the channels.
For details on the user display setting, see 5-6.(3).
For details on the user display indicating method , see
5-6.(6).
@ SAFE TITLE LEVEL Control
Th is control adjusts the safe title brightness.
@ !REMOTE NUMBER!Switch
Wh en operat ing the optiona l RCT-20 infrared remote
controller or the optional serial remot e, setting this
number
for each monitor makes it possible to
distinguish remote control for each monitor.
For "00", there is no remote control. Setti ng this
number to numbers from "01" to "99" enables you to
operate up to 99 monitors ind ividua lly.
The unit
is shipped with this number set to "00".
@ AUTO SET UP PROBE Connector
When 11.djusting the hue, chroma , and white balance
automatica lly with the optional ASP-15 auto set up
probe, connect the probe to this connector.
® Rotary Encoder
The rota ry encoder is used for such tasks as changing
the pull-out panel preset data and selecting menu and
remot e modes.
- 24 -
ll
·'·
I
. .j
,..l
<I
·1
•"j
,_
j
::J·
..
~
. .J
i::J 1·
To Next Page
Loading...
