r·
r.·-:
j :
r
r··
! .
L
L
1·
l
!.:.·
1::
\_ .
l
C
L
L
6-4. Special Function Module (SF301)
(1) Summary
This module adds Y / C input/ output, decoder output
(YPaPa), and serial remote input/output functions.
(2) Features
1) Y/C input/output
One system of Y / C input that can be looped
through with 7-pin metal connector.
2) Decoder output
(YPePa)
Since the YPePa signal is output at this connector with
high impedance, it can be used for signal checking.
3) Serial remote
The SRC-301 SERIAL REMOTE CONTROLLER provides
connectors that can centrally control monitors up to 99
units with one
coaxial cable.
This is optionally available for 17 and 18 series, too.
(3) Configuration
© SF-301: l/0 board
@ SF-301S: 1/0 board+ ROM
When conducting serial remote control using
SRC-301, SF-
301S is required because monitors before the following se-
rial numbers need to change ROM. Monitors after
the se-
rial numbers or those after the ROM version 2.1 (displayed
on the MENU screen) do not need ROM change, as these
are equipped with ROM.
Monitor
TM14-20RH/RP
TM20.20RH/RP
TM20.30RH/ RP
6-5. Auto Set Up Probe (ASP-15)
(1) Summary
Serial No.
AK2124-
AN2319-
N0402-
Th is probe makes it possible to automatic ally adjust
a 15/ 18/ 20/30 series monitoni to the factory setting
standard color temperature .
Also, user-defined data can be stored for the probe
to automatically adjust other monitors to the same
color temperature .
(2) Features
1) Automatic adjustment items
HUE (NTSC only), Chroma,
Brightness, Contrast,
G-B gain, R-G-B
background
2) 4 sets of user-defined dat a can be. stored for the
probe.
( 3) Configuration
Select one of the versions below according to the
CRT
phosphor.
6-6. Infrared Remote Control (RCT20}
(1) Summary
Using the wireless REMOTE CONTROL (RCT.20A), TM14-
17CS color monitors and 15/20/ 30 series can be controlled
up to 99 units.
(2) Features
1) Control items (*· .. 20/30 series only)
· Switching functions
COLOR/MONO, CH A/B/C, DELAY, SCAN, COMB
/T RAP, S-PAL/D-PAL, APT ON/OFF, SYNC INT/
EXT, DEGAUSS, FILE,
R-G-B SCREEN, *DISPLAY
SELECT (MENU, ENT, ESC, USER DISPLAY)
· Since ROM version 1.3
CH
A/ B/C-,. CH A/ B/C/AUX/DIGITAL
· Since ROM version 1.4
USER DISPLAY
-,. SAFE TITLE
· Preset Data change
functions
HUE, CHROMA, BRIGHTNESS, CONTRAST, R-G-B
BACKGROUND, G-B GAIN, APERTURE, *H.CENT,
*V.CENT, *H.PHASE, *HEIGHT, *WIDTH
2) Setting REMOTE NOs. on the monitor side, it is possible
to control TM14-17CS color monitors
and 15/ 20/30 series
up to 99 units.
(3) Configuration
ooDo
ooDo
oooo
DODD
'ES o o o
0000
§
~~
CUM 11 T
ODD
..,
--- llcegami :;::! COM"'°'°
RCT20A REMOTE CONTROL
The RCT-15 for 15 series can be used in the same
manner with 20/ 30 series monitors, but since the 20
/30 series have analog type manual/pr eset switching
and manual level changing, when the RCT-15
is
used ·as a 20/30 series monitor, the switch function
must be
as shown in th e figure below.
IIBNU BNT !SC S.T.
DODD
In the case of 20/ 30 series
RCT-15
- 51 -
To Next Page
Loading...
