ImpediMed SFB7 User Manual (English)

Other manuals for ImpediMed SFB7

Questions and Answers:

L
Lawrence SmithAug 8, 2025
What to do if ImpediMed SFB7 Medical Equipment shows 'Out of Range Check Leads and Electrodes'?
- J
  Joseph BlairAug 8, 2025
  If the ImpediMed Medical Equipment displays 'Out of Range Check Leads and Electrodes' or the reading seems incorrect, it indicates incorrect device setup. Here's what to check: * Verify leads are correctly fitted according to color codes. * Ensure leads are properly inserted into lead sockets. * Check for lead damage or tangling. * Confirm leads are correctly inserted into alligator clips. * Make sure alligator clips are securely attached to electrodes. * Use fresh electrodes. * Perform a calibration check to identify device faults, ensuring correct color coding and snug lead insertion into the test cell.
J
Jay CainAug 13, 2025
Why is there no display when my ImpediMed Medical Equipment SFB7 is switched on?
- D
  Danielle GriffinAug 13, 2025
  If your ImpediMed Medical Equipment SFB7 shows no display when switched on, the possible causes are: * Low battery power. * No external power. To resolve this: 1. Attach an external power pack and try again. 2. If the external power pack is already attached, ensure it is properly plugged in and switched on.
R
robert01Aug 17, 2025
How to fix ImpediMed SFB7 when it stops responding to touch screen?
- D
  Danielle BeanAug 17, 2025
  If your ImpediMed Medical Equipment stops responding to touch screen commands, it may be due to an internal software fault. Try powering the device off and then on again. Report the fault to ImpediMed.
R
Rebecca ClarkAug 21, 2025
What to do if ImpediMed SFB7 Medical Equipment shows "Out of Range Check Leads and Electrodes"?
- T
  Timothy VillarrealAug 21, 2025
  If the message "Out of Range Check Leads and Electrodes" appears on the screen, or the reading seems incorrect, it may be due to an incorrect device setup. To resolve this, follow these steps: 1. Ensure the leads are correctly fitted according to the color coding. 2. Make sure the leads are properly inserted into the lead sockets. 3. Check that the leads are not damaged or tangled. 4. Verify the leads are properly inserted into the alligator clips. 5. Ensure the alligator clips are securely attached to the electrodes. 6. Use fresh electrodes. 7. Perform a calibration check to determine if the device is faulty. 8. If performing the calibration check, ensure the color coding is correct and the leads are pushed snugly into the test cell.
T
Tommy CraneAug 25, 2025
Why does ImpediMed SFB7 Medical Equipment stop responding to touch screen commands?
- K
  Kim BoothAug 26, 2025
  If your ImpediMed Medical Equipment device stops responding to touch screen commands, it might be due to an internal software fault. Try powering the device off and then on again. If the issue persists, report the fault to ImpediMed.
E
Eric TapiaAug 29, 2025
How to fix no display on ImpediMed Medical Equipment SFB7?
- J
  josephfordAug 29, 2025
  If there is no display when your ImpediMed Medical Equipment SFB7 is switched ON, it could be due to low battery power or a lack of external power. First, try attaching an external power pack. If one is already attached, ensure it is properly plugged in and switched on.
L
Laura FrancoSep 3, 2025
What does it mean if the power light is blinking on ImpediMed Medical Equipment?
- S
  Sergio NguyenSep 3, 2025
  If the power light on your ImpediMed Medical Equipment is blinking, red, or orange, this is normal behavior. Please refer to the section titled "Battery Status Indicator" for more information.

ImpediMed SFB7 Specifications

General

Brand	ImpediMed
Model	SFB7
Category	Medical Equipment
Language	English

ImpediMed SFB7 Use And Cleaning

Table of Contents

Other manuals for ImpediMed SFB7

Questions and Answers:

ImpediMed SFB7 Specifications