intelligent motion systems, inc.
Excellence in Motion
TM
QUICK REFERENCE
370 N. MAIN ST., PO BOX 457, MARLBOROUGH, CT 06447
PH: (860) 295-6102, FAX: (860) 295-6107
Internet: www.imshome.com, E-Mail: info@imshome.com
TM
MicroLYNX EXPANSION MODULE
ISOLAISOLA
ISOLAISOLA
ISOLA
TED COMMUNICATED COMMUNICA
TED COMMUNICATED COMMUNICA
TED COMMUNICA
TIONS MODULESTIONS MODULES
TIONS MODULESTIONS MODULES
TIONS MODULES
FOR CAN FOR CAN
FOR CAN FOR CAN
FOR CAN
VERSION MICRVERSION MICR
VERSION MICRVERSION MICR
VERSION MICR
OLOL
OLOL
OL
YNX ONLYNX ONL
YNX ONLYNX ONL
YNX ONL
YY
YY
Y
Isolated Communications Quick Reference Guide
The primary function of this guide is to acquaint the user
with the specifications and configuration of the CAN
Version MicroLYNX Isolated Communications Modules. The
full MicroLYNX product manual is available in Acrobat PDF
format on the IMS Product CD. It also may be downloaded
from the IMS web site at www.imshome.com.
Notes And Warnings
Please observe the following when handling, connecting
and using your MicroLYNX Expansion Modules. Failure to
observe these points may result in damage. All warranty
and disclaimer information is located in the full product
manual and should be referenced for more information.
Thermal Specifications
Range
Operating Temperature ................................................... 0 to +50°C
Storage Temperature ................................................... -20 to +70°C
Humidity.................................................... 0 to 90% non-condensing
Mechanical Specifications
Dimensions in Inches (mm)
Electrical Specifications
RS-232 Receiver
Input Voltage Range ................................................ ±30 Volts
Input Threshold Low ................................................. 0.4 Volts
Input Threshold High ................................................ 2.4 Volts
Input Resistance ........................................................ 3 to 7 kΩ
RS-232 Transmitter
Output Voltage Swing ................................................. ±5 Volts
Output Resistance ............................................................ 300 Ω
Output Short Circuit Duration ...................... Continuous
RS-485 Receiver
Input Voltage Range ............................. -8 to +12.5 Volts
Input Differential Threshold................... ±200 Millivolts
Input Resistance .................................................................96 kΩ
Driver
Differential Output (R=50 Ω) ................................... 2 Volts
Output Voltage Range ......................... -8 to +12.5 Volts
The MicroLYNX Expansion Module components are sensitive to
Electrostatic Discharge (ESD). All handling should be done at an
ESD protected workstation.
Hazardous Voltage Levels may be present if using an open frame
power supply to power the MicroLYNX Controller and Modules.
Do not connect or disconnect the AC power or the motor leads
with the AC power on.
© Intelligent Motion Systems, Inc.Revision 090805
MicroLYNX Slot Usage
The Isolated Communications Expansion Modules may only
be used in Slot 2 of the CAN Version MicroLYNX.
The RS-232 and RS-485 Expansion Modules CANNOT be
used together.
egasUtolSnoisnapxEXNYLorciM
noisnapxE
eludoM
1tolS 2tolS 3tolS
mumixaM
dewollA
latigiDdetalosI
0/I
seYseYseY3
deepShgiH
O/IlaitnereffiD
oNseYseY2
golanA
kcitsyoJ/tupnI
seYseYseY1
detal
osI
noitacinummoC
oNseYoN1
tuptuOgolanAseYseYseY2
O/IlennahC21seYseYoN1
NOTE: The 8 Pin Terminal Block is supplied with the mating connector. The10 Pin
Header is NOT SUPPLIED with a mating connector. (Use AMP 3-1437026-4 or
equivalent).
Both the RS-232 and the RS-485 Expansion Modules utilize the
MicroLYNX COMM 2 port. Therefore, the two Modules
CANNOT be used in conjunction with each other. Only one of
the two interfaces can be used with the CAN Version Micro-
LYNX at any given time.
2.184
(55.47)
0.970
(24.64)
0.50
(12.7)
8 Pin
Terminal
Pin 1
Pin 8
0.423
(10.74)
10 Pin
Header
Pin 1
Pin 10
O
N
1
2
3
4
5
6
To Next Page
Need help?
General
