Indesit DFC 2B+19 AC User Manual (English)

Questions and Answers:

M
Mr. Paul Robinson MDAug 13, 2025
What to do if my Indesit Dishwasher won’t start or does not respond to commands?
- K
  kingmeganAug 13, 2025
  If your Indesit dishwasher won't start or respond, first, ensure it's properly plugged into the socket. If there was a power outage, press the START/Pause button to resume the cycle, as it won't restart automatically. Check that the door is fully closed until you hear a click. If the door was opened for more than 4 seconds during a cycle, close it and press START/Pause. If it still doesn't respond, try switching it off and on again after a minute. If the issue continues, unplug it for a minute, then plug it back in.
W
Whitney BraunAug 17, 2025
Why won’t my Indesit Dishwasher drain?
- S
  stephenjohnsonAug 17, 2025
  If your Indesit dishwasher isn't draining, first, wait until the wash cycle finishes. Then, check the drain hose to ensure it's not bent. Also, inspect the sink drain pipe for any blockages and clean it if necessary. Lastly, check the filter for food residues and clean it.
M
Mr. Stanley LewisAug 20, 2025
How to fix Indesit DFC 2B+19 AC Dishwasher when it does not fill the water and all LEDs are blinking rapidly?
- J
  johnsonkathleenAug 20, 2025
  If your Indesit dishwasher is not filling with water and all the LEDs are blinking rapidly, ensure that the tap is open and there is water in the water supply. Check that the inlet hose is not bent. Also, the sieve in the water inlet hose may be clogged and needs cleaning. After checking these, turn the dishwasher off and on, then restart a new program.
R
richardthompsonAug 25, 2025
Why is my Indesit DFC 2B+19 AC Dishwasher making excessive noise?
- C
  Claudia SchneiderAug 25, 2025
  If your Indesit dishwasher is making excessive noise, make sure the dishes are not rattling against each other by positioning the crockery correctly. If there's an excessive amount of foam, it indicates that the detergent was either measured incorrectly or is unsuitable for dishwashers. Restart the dishwasher by pressing the DRAIN button and run a new program without detergent.
F
fritzrobertAug 28, 2025
Why are the dishes not clean after using my Indesit Dishwasher?
- K
  kpetersAug 28, 2025
  If dishes are not clean after a cycle in your Indesit dishwasher, ensure the crockery is arranged correctly so the spray arms can rotate freely. Select an appropriate wash cycle for the load. Make sure the cap on the rinse aid compartment is closed correctly. Check if the filter is soiled or clogged and clean the filter assembly. Also, ensure there is salt in the salt reservoir and refill if needed.
J
Jose MeyerSep 1, 2025
Why is the salt indicator lit on my Indesit Dishwasher?
- C
  Catherine ParrishSep 1, 2025
  If the salt indicator is lit on your Indesit dishwasher, it means the salt reservoir is empty. Refill it with salt. Note that the indicator may remain lit for several wash cycles after refilling. Also, adjust the water hardness according to the table provided.
D
Daniel DiazSep 4, 2025
What to do if Indesit Dishwasher finishes the cycle prematurely?
- D
  David ButlerSep 4, 2025
  If your Indesit dishwasher is finishing cycles prematurely, check if the end of the drain hose is placed at the correct height. Also, check for siphoning into your home sewage system and install an air admittance valve if needed. Inspect the water supply for leaks or other issues that might be letting air inside.
W
whoffmanSep 8, 2025
Why is the rinse aid indicator lit on my Indesit DFC 2B+19 AC Dishwasher?
- C
  Charles DennisSep 8, 2025
  If the rinse aid indicator is lit on your Indesit dishwasher, it means the rinse aid dispenser is empty. Refill the dispenser with rinse aid. Note that the rinse aid indicator may remain lit for several wash cycles after refilling.

Indesit DFC 2B+19 AC Specifications

General

Appliance placement	Freestanding
Control panel colour	White
Inlet hose length	1.5 m
Outlet hose length	1.5 m
Noise emission class	C
Noise level	49 dB
Number of washing programs	6
Drying system	Static
Cycle time	190 min
Delayed start timer	Yes
Power consumption (off)	0.5 W
Connected load	1900 W
Energy consumption (standby)	0.5 W
AC input voltage	220-240 V
AC input frequency	50 Hz
Height	85 cm
Half Load Option	Yes
Drying Efficiency Class	A
Number of place settings	13
Washing programs	Eco, Intensive, Normal
Delay start (max)	24 hours
Width	600 mm
Depth	600 mm