Why do my dishes have a bluish tinge from my Indesit DSG 263 Dishwasher?
If your dishes have streaks or a bluish tinge after being washed in your Indesit dishwasher, the rinse aid dosage is likely too high. Adjust the rinse aid dosage to a lower setting.
Why are dishes not clean after washing in my Indesit Dishwasher?
If your dishes aren't coming out clean from your Indesit Dishwasher, several factors could be at play. Check if the racks are overloaded or if the crockery hasn't been arranged well. Make sure the sprayer arms can move freely and that you're using an appropriate wash cycle. Also, verify that the detergent is measured correctly and is suitable for dishwashers. Ensure the lid on the rinse aid compartment is shut correctly, the filter isn't dirty or blocked, and the refined salt level isn't low.
What to do if my Indesit DSG 263 won't drain water?
If water isn't draining from your Indesit Dishwasher, it might be because the cycle hasn't finished yet. Check if the water inlet hose is bent or if the drain duct is blocked. Also, the filter might be clogged with food residues.
Why aren't the dishes drying properly in my Indesit Dishwasher?
If your crockery isn't drying properly in your Indesit Dishwasher, it could be due to selecting a wash cycle without a drying program. Also, the rinse aid might be used up, or the dosage is too low. Check if the rinse aid dispenser setting isn't high enough.
Why are the dishes not clean in my Indesit DSG 263?
Your dishes might not be clean due to several reasons: * The racks are overloaded. * The crockery has not been arranged well. * The sprayer arms cannot move freely. * The wash cycle is too gentle. * An excessive amount of foam has been produced because the detergent has not been measured out correctly or it is not suitable for use in dishwashers. * The lid on the rinse aid compartment has not been shut correctly. * The filter is dirty or blocked. * The refined salt level is low.
Why is my Indesit Dishwasher making so much noise?
Excessive noise from your Indesit Dishwasher can occur if the dishes are rattling against each other or against the sprayer arms. Also, it might be caused by an excessive amount of foam due to incorrect detergent measurement or using a detergent not suitable for dishwashers.
Why are my dishes not clean after using my Indesit Dishwasher?
If your dishes aren't clean after a wash in your Indesit dishwasher, the racks might be overloaded, or the crockery hasn't been arranged well. The sprayer arms might not be moving freely, or the wash cycle is too gentle. Too much foam could have been produced, or the lid on the rinse aid compartment isn't shut correctly. The filter might also be dirty or blocked, or the refined salt level is low. Check the loading, arrangement, sprayer arms, cycle selection, detergent and rinse aid usage, filter, and salt levels.
Why does my Indesit DSG 263 Dishwasher leave a white film on dishes?
If your dishes and glasses are covered in a white film or limescale deposits after using your Indesit Dishwasher, the level of refined salt might be low, or the dosage setting might not be suited to the hardness of the water. Also, ensure the lid on the salt dispenser is closed properly. The rinse aid might be used up, or the dosage could be too low. Note that the crockery might be made from non-stick material.
Why Indesit DSG 263 is not taking water and the drying and end indicator lights flash?
If your Indesit Dishwasher isn't taking in water and the Drying and End indicator lights are flashing, there might be no water in the mains supply, or the water inlet hose could be bent. Turn on the tap; the appliance should start after a few minutes. If indicator lights were flashing and no action was taken, the appliance might be locked. To unlock it, switch off the machine using the ON/OFF button, turn on the tap, and switch the machine back on after 20 seconds by pressing the same button. Reprogram the machine and restart the wash cycle.
What to do if Indesit Dishwasher won't take in water and beeps?
If your Indesit dishwasher isn't taking in water and is emitting beeps, there might be no water in the mains supply, or the water inlet hose could be bent. Try turning on the tap; the appliance should start after a few minutes. Also, the appliance lock may have been activated. Turn off the dishwasher with the ON/OFF button, turn on the tap, and switch the appliance back on after 20 seconds. Then, reprogram and restart the wash cycle.
Connects the dishwasher to the cold or hot water supply.
System to prevent water leaks and floods.
Instructions for safe connection to the power supply.
Step-by-step guide to begin a wash cycle.
Guidance on correct detergent use and compartment loading.
Steps to disconnect power and water before maintenance.
Instructions for cleaning water inlet and main filters.
Important safety rules for using the appliance.
Solutions for appliance not starting or being controlled.
Solutions for door closure and water drainage issues.
Solutions for noise, limescale, film, streaking, or dishes not clean.
Solutions for water intake, hose, or filter blockage alarms.
General| Type | Freestanding |
|---|---|
| Size | Slimline |
| Energy efficiency class | A |
| Washing performance class | A |
| Drying performance class | A |
| Number of programmes | 6 |
| Delay Start | Yes |
| Half Load Option | Yes |
| Weight | 39 kg |
| Water consumption per cycle | 11 liters |
| Dimensions (H x W x D) | 85 cm x 45 cm x 60 cm |
To Next Page
