infinite spa CHAMPION

Questions and Answers

S
Sandra WelchAug 16, 2025
What to do if my infinite spa CHAMPION Hot Tub heater is not working?
- S
  Steven VillegasAug 16, 2025
  If the heater in your infinite spa Hot Tub isn't working, there are several potential causes and solutions: * Ensure the temperature is set high enough (between 20-40°C). * Remember the heating system may not start immediately due to a delay related to the temperature sensor's tolerance. * Check and replace the filter cartridge if it's dirty. * Make sure the water level is adequate and top it up if needed. * As a general troubleshooting step, disconnect the power supply, wait 10 minutes, and then switch it back on.
P
Patrick HernandezAug 19, 2025
What to do if my infinite spa CHAMPION Hot Tub filter system is not working?
- U
  uriceAug 19, 2025
  If the filter system in your infinite spa Hot Tub isn't working, consider these possible causes and solutions: * Replace the filter cartridge if it's dirty. * Ensure the water level is sufficient; top it up if necessary. * Try disconnecting the power supply, waiting 10 minutes, and then reconnecting it.
M
Mary McculloughAug 22, 2025
Why is my infinite spa CHAMPION losing water?
- L
  Lauren MarshallAug 22, 2025
  If your infinite spa Hot Tub is losing water, there could be a few reasons: * Check the sealing plug at the bottom of the spa; clean it and tighten it by hand into the drain opening. * Increase the filtering time. * Replace the filter cartridge if it is dirty.
S
Shane GarrisonAug 25, 2025
What does error code FH mean on my infinite spa CHAMPION?
- B
  brian68Aug 25, 2025
  Error code FH with a warning sound indicates that the filtering and heating in your infinite spa Hot Tub have been running for 72 hours. To resolve this, replace the filter cartridge and press the HEATER button to restart the filtering and heating process.
P
phyllis42Aug 27, 2025
How to fix error code SL on infinite spa Hot Tub?
- T
  teresa78Aug 28, 2025
  If you see error code SL on your infinite spa Hot Tub, it indicates a filter pump malfunction. You can try performing a reset by switching the power off and then back on after 10 minutes. If that doesn't work, consider replacing the motor block.
K
Kathy BrownAug 30, 2025
How to fix error code HL on infinite spa CHAMPION Hot Tub?
- R
  Richard WilsonAug 30, 2025
  If your infinite spa Hot Tub displays error code HL, it suggests a temperature sensor malfunction. Attempt a reset by turning the power off, waiting 10 minutes, and then turning it back on. If the problem persists, the motor block may need to be replaced.
M
Michael HuffSep 2, 2025
How to fix error code SH on infinite spa Hot Tub?
- S
  Stephen AcostaSep 2, 2025
  If you're seeing error code SH on your infinite spa Hot Tub display, it indicates a circuit board or temperature sensor malfunction. Try a reset by switching the power off and then back on after 10 minutes. If the issue continues, you might need to replace the display or the motor block.
R
Rachel YoungSep 5, 2025
Why is my infinite spa CHAMPION Hot Tub filter pump running too loud?
- M
  Mark BellSep 5, 2025
  If your infinite spa Hot Tub filter pump is running too loudly, here are a few things to check: * Replace the filter cartridge if it's dirty. * Ensure the water level is adequate; add water if it's too low. * Clean the cover on the filter cartridge.
C
Christopher McdonaldSep 7, 2025
How to fix massage jet system not working in infinite spa Hot Tub?
- J
  Jill JonesSep 7, 2025
  If the massage jet system in your infinite spa Hot Tub isn't working, it could be due to a couple of reasons: * The massage jet motor may be overheating. If so, wait for it to cool down, then press the JET button to activate the function. * There might be a problem with the filter, air and massage jets, or the heater unit. In this case, disconnect the power supply, wait 10 minutes, and then switch the power back on.
K
Katherine CrossSep 10, 2025
How to fix air jet system not working in infinite spa Hot Tub?
- T
  Taylor WardSep 10, 2025
  If the air jet system in your infinite spa Hot Tub isn't working, here are a couple of things to try: * The air fan motor may be overheating. If this is the case, wait for it to cool down, and then press the BUBBLE button to activate the function. * There might be an issue with the filter, air and massage jets, or heater unit. Try disconnecting the power supply, waiting 10 minutes, and then switching the power back on.