Infinity Boss.three - User Manual

www.infinitycycleworks.com
CorrectIncorrect
A
B
D
C
GETTING STARTED
HANDLEBAR ASSEMBLY
Remove all protective packaging from the handlebar assembly, if not already done.
Turn the fork of the bicycle to face forward. (Note that "forward" means that the wheel
mounting slots are in the furthest forward position, so the wheel axle will be in front of
the fork when assembled.) Look for removable decal and information card on the fork
showing the proper direction.
(A)
If your model comes equipped with gears and/or handbrakes, you will need to be sure
that the brake cables and shift cables are properly routed. Position the handlebar
assembly as if you were going to install it and take a look at the cables. They should
run in a smooth arc from the shifter or brake lever to the front brakes or cable stop on
the frame. If they are twisted or kinked, the shifting and braking will not work. Rotate
the handlebars around until the cables are taking the smoothest route.
(D)
Loosen the center bolt
(B) enough so that the wedge and stem can slide into the fork
steer tube. Lower the stem until the mark that says "minimum insertion" is no longer
visible. Tighten the stem center bolt so that the handlebar assembly is in line with the
fork. If needed, you can recheck this after the front wheel is installed and re-adjust.
Check handlebar stem clamp bolt
(C) to be sure they are properly tightened and
handlebar cannot move. The angle of the handlebar can be adjusted. To adjust: loosen
all of the handlebar stem clamping bolts and rotate the handlebar to the desired
angle. Be sure that the handlebar stays centered in the stem. Re-tighten the bolts a
little at a time
, being sure that the gap between the stem cap and stem stays even.
Repeat tightening each bolt a little bit until handlebar is secure.
Open the carton from the top and carfully remove the bicycle. Now remove all ties and
protective wrapping making note of parts as you go along. Do not discard packing
material until assembly is complete to ensure no required parts are accidentally
discarded.
Here is a picture of your assembled
bicycle.
Be sure to double check that all
quick release and bolts are secure
before riding.
Always wear a helmet.
TOOLS FOR ASSEMBLY ARE INCLUDED
Your new bicycle was assembled and tuned in the factory and then partially disassembled for shipping. The following instructions will enable you to
prepare your bicycle for years of enjoyable cycling. For more details on inspection, lubrication, maintenance and adjustment of any area, please refer
to the relevant sections in your owner’s manual. Should you require replacement parts or have any questions pertaining to the assembly of your
bicycle, call our service line direct at:
Pedals
Frame
Handlebar assembly
Front wheel
Quick Release
Seat
Seat post
ASSEMBLY
VIDEO LINK
Boss.three 700c Men’s Hybrid Bicycle

Summary

Getting Started

Unpacking and Initial Preparation

Open carton, remove all ties and protective wrapping. Keep packing material until assembly is complete.

Handlebar Assembly

Stem and Cable Setup

Route cables smoothly, insert stem to minimum insertion mark, align with fork, and adjust handlebar angle.

Front Wheel Installation

Quick Release Skewer Method

Install front wheel using quick release skewer, ensuring proper tension and brake clearance.

Nutted Front Wheel Installation

Axle Nut Method

Install front wheel using axle nuts and retainer washers, ensuring proper torque and free spin.

Saddle Assembly

Seat Post Insertion and Adjustment

Insert seat post past minimum insertion mark and adjust saddle height and level securely.

Pedals and Cranks

Correct Pedal Attachment

Attach pedals correctly (left/right) by hand to avoid stripping threads, then tighten securely.

Final Checks and Safety

Pre-Ride Inspection

Check tire pressure, secure quick releases/nuts, test gears, and ensure all accessories are tight.

Infinity Boss.three Specifications

General

Type	Mountain Bike
Frame Material	Aluminum
Number of Gears	21
Wheel Size	27.5 inches
Weight	14.5 kg
Brakes	Disc
Suspension	Front