Ingersoll-Rand AVC13 - User Manual

Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 1999
Printed in U.S.A.
03528742
Form P6408
Edition 12
June, 1999
OPERATION AND MAINTENANCE MANUAL
FOR MODELS AVC10, AVC12, AVC13,
AND AVC26 LIGHTWEIGHT RIVETING HAMMERS
Models AVC10, AVC12, AVC13 and AVC26 Lightweight Riveting Hammers are designed for
riveting door and window frames, sheet metal, lightweight plate and riveting skin on all types of
air and spacecraft.
Ingersoll–Rand is not responsible for customer modification of tools for applications on which
Ingersoll–Rand was not consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
• Always operate, inspect and maintain this tool in
accordance with American National Standards
Institute Safety Code for Portable Air Tools
(ANSI B186.1).
• For safety, top performance, and maximum durability
of parts, operate this tool at 90 psig (6.2 bar/620 kPa)
maximum air pressure at the inlet with 1/2” (13 mm)
inside diameter air supply hose.
• Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting
any accessory on this tool, or before performing any
maintenance on this tool.
• Do not use damaged, frayed or deteriorated air hoses
and fittings.
• Be sure all hoses and fittings are the correct size and
are tightly secured. See Dwg. TPD905–1 for a typical
piping arrangement.
• Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
• Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
• Do not remove any labels. Replace any damaged label.
USING THE TOOL
• Always wear eye protection when operating or
performing maintenance on this tool.
• Always wear hearing protection when operating this
tool.
• Keep hands, loose clothing and long hair away from
impacting end of tool.
• Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
• Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended air
pressure.
• Tool accessory may continue to impact briefly after
throttle is released.
• Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may be
harmful to your hands and arms. Stop using any tool
if discomfort, tingling feeling or pain occurs. Seek
medical advice before resuming use.
• Use accessories recommended by Ingersoll–Rand.
• Never operate a Percussion Tool unless an accessory is
properly installed and the tool is held firmly against
the work.
• Always use a retainer, when furnished, in addition to
proper barriers to protect persons in surrounding or
lower areas from possible ejected accessories.
• This tool is not designed for working in explosive
atmospheres.
• This tool is not insulated against electric shock.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool performance, and
increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized Servicenter.
F
E
P
TPD1378

Summary

Placing Tool in Service

Using the Tool

Essential safety precautions and operational best practices for tool usage.

Warning Label Identification

Percussive Tool Warnings

Critical safety advice for operating percussive riveting hammers.

Adjustments

Setting the Power Regulator

Detailed steps on how to adjust the power output of the riveting hammer.

Placing Tool in Service

Lubrication

Instructions for lubricating the tool for optimal performance and longevity.

Specifications

Maintenance Section

Disassembly

Steps for taking the tool apart for repair or replacement of parts.

Assembly

Steps for reassembling the tool after maintenance or repair operations.

Troubleshooting Guide

A guide to identify and resolve common problems and issues with the tool.

Ingersoll-Rand AVC13 Specifications

General

Brand	Ingersoll-Rand
Model	AVC13
Category	Tools
Language	English