INNOVAPLAS BILTMOR 5015 - User Manual

REV. 02/12/2020 PN: PG:1
2257 route 139
Drummondville, Québec
J2A 2G2
1 year on step and ladder.
1 year on hardware.
MANUFACTURER WARRANTY
WWW.INNOVAPLAS.COM
WARNING
Install the step on a flat surface.
Do not jump or dive from the step or ladder.
Remove the step from water when temperatures drop below freezing.
In winter, the step should be stored in an area protected from snow.
Never lift the step by its handrails.
Use BATTERY operated tools to avoid electric shock near water.
Ensure no corrosive materials are added to the step or harware kit.
The step must be installed per manufacturer’s instructions.
File off all stripped or sharp edges before assembly to avoid injuries
and liner damage.
The manufacturer is not responsible for damages or injuries caused
by improper installation or use of product.
To ease the installation of handrails and bolts, use a screwdriver to
line up the holes.
Required tools (not included)
A
2X
GUSSET
INSERT NUT
1) Insert the two gussets in the slots and slide them
toward the corners.
2) Assemble the two main modules with the six screws,
nuts and washers provided.
3) Snap the door between the top and bottom module
within the slots provided.
Sand
(not included)
Sand
20 lbs
x6
x6
x6
A B C
Phillips #2
Phillips #3
7/16 wrench
Phillips bit
BILTMOR 5015 WITH CLASSIC LADDER 6003
Contents of the Biltmor box SKU # 5015
Security straps
x2
x2
x2
x2
(3/4 IN.)
x18
2 1/2 IN.)
x2
SCREW BAG 140-0058
(1 IN.)
F
A D B C
Contents of the ladder box SKU # 6003
x2
x2
x2
x2
MAXIMUM functional
width is 1/4’’.
A weather-resistant
padlock is recommended
(not included).
3/8 drill bit
SCREW BAG 140-0036
x6 x6 x6
(1 IN.)
(³⁄4 IN.)
x2
(³⁄4 IN.)
x13
A
B C D E
x2
x2
x3
x2
x2
Maximum weight: 300 lbs / 136 kg.

Summary

General Safety and Installation Guidelines

Warning: Critical Safety and Installation Precautions

Highlights crucial safety warnings including installation on a flat surface, avoiding diving, winter storage, not lifting by handrails, using battery tools near water, avoiding corrosive materials, and maximum weight limits.

Required Tools for Assembly

Essential Tools List

Lists necessary tools such as 3/8 drill bit, Phillips bits (#2, #3), and a 7/16 wrench, noting that these are not included with the product.

Assembly Step B: Ladder Base Assembly

Attaching Post Ends and Feet

Instructions for snapping post ends into the step, securing the filler post, and attaching the two feet to the bottom of the step.

Assembly Step C: Main Structure Assembly

Connecting Posts and Handrails

Details on inserting large and 35" posts, securing them with screws, attaching the platform, and installing handrails, leaving small ones floating.

Assembly Step D: Ballast Installation

Adding Weight for Stability

Guidance on placing a 20 lbs (9 kg) sand bag on the third step to ensure stability during use.

Assembly Step E: Submerging the Step

Pool Entry Procedure

Instructions for slowly submerging the assembled step into the pool without damaging the liner and purging all air.

Assembly Step F: Securing the Platform

Attaching Platform to Pool Seat

Describes securing the platform to the top seat using provided straps and optional screws for enhanced rigidity.

Assembly Step G: Ladder Attachment

Connecting Ladder to Posts and Platform

Details on tracing marks, sliding pivot blocks, attaching the ladder base, securing the platform, and inserting post covers.

Assembly Step H: Final Ladder Securing

Securing Ladder to Pivot Blocks

Instructions for attaching the ladder to the pivot blocks using bolts, washers, and nuts, and drilling a hole for the sliding lock.

Padlock Installation and Safety Lock

Securing the Ladder with a Lock

Details on using a sliding lock as a guide for drilling and securing the ladder in an upright position to prevent unauthorized entry.

INNOVAPLAS BILTMOR 5015 Specifications

General

Model	BILTMOR 5015
Type	Step Ladder
Steps	5
Category	Ladders
Load Capacity	225 lb
Weight Capacity	225 lb
Height	5 ft
Weight	7.5 kg