Inovance ISMH3-13C15CD-U Y Series - User Manual

109 pages

To Next Page

To Next Page

Loading...

Table of Contents

Questions and Answers:

M
Maria ScottSep 12, 2025
How do I troubleshoot an Inovance ISMH3-13C15CD-U Y Controller if the LED display is off or doesn't show "rdy"?
- G
  garciacindySep 12, 2025
  If the LED display of your Inovance Controller is not on or doesn't show "rdy", it could be due to several reasons. First, the control power voltage might be abnormal, so measure the AC voltage between L1C and L2C. Second, the main power voltage might be abnormal; for a single-phase 220 V model, measure the AC voltage between L1 and L2. If the DC bus voltage amplitude (voltage between P and -) is lower than 200 V, "nrd" will be displayed. Third, the program burning terminal might be shorted, so check it. Finally, the servo drive itself might be faulty.
V
Veronica WilsonSep 13, 2025
What causes unsteady motor speed in Inovance ISMH3-13C15CD-U Y Controller?
- T
  tgeorgeSep 13, 2025
  If the motor speed of your Inovance Controller is not steady, perform automatic gain tuning, as the gain might be set unreasonably.
P
Patrick BarnesSep 15, 2025
Why does the motor shaft of my Inovance Controller vibrate left and right?
- E
  Elizabeth LeonardSep 15, 2025
  If the motor shaft vibrates left and right, it might be because the load inertia ratio (H08-15) is too large. Perform inertia auto-tuning and automatic gain tuning on your Inovance Controller.

Inovance ISMH3-13C15CD-U Y Series Specifications

General

Category	Controller
Control Mode	Vector control
Protection Level	IP20
Series	Y Series
Communication Interface	RS485
Operating Temperature	-10°C to +40°C
Storage Temperature	-20°C to +60°C
Humidity	5% to 95% (non-condensing)
Altitude	≤1000m

Summary

Safety Information and Precautions

Electrical Safety Guidelines

Machine and Personnel Safety

Electrical Installation Safety

Electrical Shock Hazard Precautions

Specific warnings and measures to prevent electrical shock hazards.

Chapter 2 Wiring

2.1 Servo System Wiring

Chapter 4 Quick Setup

Setup Flowchart and Modes

Chapter 5 Troubleshooting

5.1 During Startup Troubleshooting

Common issues and solutions encountered during initial servo drive startup.

5.2 During Running Troubleshooting

Troubleshooting procedures for problems occurring while the servo drive is operating.

Troubleshooting Faults

Detailed guide for diagnosing and resolving specific fault codes and errors.

Troubleshooting Warnings

Chapter 6 Parameter Table

Servo Motor Parameters

Comprehensive list and description of parameters related to the servo motor.

Servo Drive Parameters

Parameters specific to the servo drive's firmware and identification.

Control and Terminal Parameters

Motion Control Parameters

Parameters related to position, speed, and torque control functions.

Tuning, Protection, and Monitoring Parameters

Parameters for gain tuning, fault protection, and system monitoring.

Related product manuals

ISMH3-18C15CD-U Y Series

ISMH3-85B15CD-U Y Series

ISMH3-29C15CD-U Z Series

ISMH1-20B30CB-U Z Series

ISMH1-40B30CB-U Z Series

ISMH1-75B30CB-U Z Series

ISMH4-40B30CB-U Z Series

ISMH4-75B30CB-U Z Series

Preview: Inovance inovance

Inovance inovance

Inovance MD500T45GB-INT

Inovance MD500T132G-INT

Inovance MD500T110G-INT