EasyManua.ls Logo

INOXPA SLR Series - User Manual

INOXPA SLR Series
56 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
INSTALLATION, SERVICE AND MAINTENANCE INSTRUCTIONS
LOBE PUMP
SLR
Original Instructions
01.500.30.03EN
(0) 2019/12
01.500.32.0001

Questions and Answers

  • J
    Jonathon GomezAug 14, 2025
    What to do if the INOXPA SLR suction pipe is clogged?
    • N
      Nathan RodriguezAug 14, 2025
      If the suction pipe of your INOXPA Water Pump is clogged, you should check the suction pipe and filter(s), if any, to resolve the issue.
  • J
    Joseph HobbsAug 17, 2025
    How to fix an INOXPA SLR Water Pump that sucks in air?
    • S
      Shannon ClarkAug 17, 2025
      If your INOXPA Water Pump is sucking in air, check the suction pipe and all its connections to ensure they are properly sealed.
  • B
    brownelizabethAug 21, 2025
    How to resolve motor overload in an INOXPA Water Pump?
    • M
      Maureen PetersonAug 21, 2025
      To resolve motor overload in your INOXPA Water Pump, invert the rotation direction.
  • V
    Vincent JohnsonAug 25, 2025
    What to do if INOXPA Water Pump is not purged?
    • B
      Benjamin HarperAug 26, 2025
      If your INOXPA Water Pump is not purged, you should purge or fill it to resolve the issue.
  • T
    Tyler DavisAug 29, 2025
    How to manage high liquid viscosity in INOXPA SLR Water Pump?
    • D
      Dr. Howard StephensAug 29, 2025
      If the viscosity of the liquid is too high in your INOXPA Water Pump, you can reduce the viscosity by, for example, heating the liquid, or reduce the pump speed.
  • M
    Mark LucasSep 1, 2025
    How to manage low liquid viscosity in INOXPA SLR?
    • B
      Brenda Scott MDSep 1, 2025
      If the viscosity of the liquid is too low in your INOXPA Water Pump, increase the viscosity by, for example, by cooling the liquid, or increase the pump speed.
  • V
    veronica43Sep 5, 2025
    How to reduce high liquid temperature in INOXPA Water Pump?
    • V
      vwardSep 5, 2025
      If the temperature of the liquid is too high in your INOXPA Water Pump, reduce the temperature by cooling the liquid.
  • J
    John PerezSep 9, 2025
    What to do if the lobes are worn in INOXPA SLR Water Pump?
    • W
      Walter MasonSep 9, 2025
      If the lobes are worn in your INOXPA Water Pump, replace the lobes.

Summary

Safety

General Safety Instructions

Essential safety guidelines for installation, operation, and maintenance.

Installation

Relief Valve (Pressure Bypass)

Guidance on installing and understanding the function of the pressure relief valve.

Electrical Installation

Safety precautions and steps for connecting the electric motor and control systems.

Start-up

Pre-Start and Start-up Checks

Essential checks before and during initial pump operation to ensure safety and performance.

Troubleshooting

Common Pump Issues and Solutions

A table detailing probable causes and solutions for common pump operating problems.

Maintenance

Pump Disassembly and Assembly

Detailed procedures for disassembling and reassembling pump components.

Technical Specifications

INOXPA SLR Series Specifications

General IconGeneral
PressureUp to 12 bar
ViscosityUp to 1, 000, 000 cP
MaterialsStainless Steel AISI 316L
Seal TypeMechanical Seal
ConnectionsTri-Clamp
MotorElectric

Related product manuals