EasyManua.ls Logo

Insignia NS-BK2TSS6 - User Manual

Insignia NS-BK2TSS6
29 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Before using your new product, please read these instructions to prevent any damage.
USER GUIDE
Single- and Dual-Tap
Kegerator/Beverage
Cooler
NS-BK1TSS6/NS-BK2TSS6
NS-BK1TSS6_NS-BK2TSS6_15-0765_MAN_V3_ENG.fm Page 1 Tuesday, December 22, 2015 6:20 PM

Table of Contents

Questions and Answers

  • T
    Thomas BowenAug 14, 2025
    What to do if no beer flows from my Insignia Beverage Dispenser?
    • N
      Nicole CharlesAug 14, 2025
      If there's no beer flowing from your Insignia Beverage Dispenser, several factors could be at play. First, ensure your CO₂ tank isn't empty and that both the CO₂ tank valve and regulator shutoff valve are open. Also, check if the beer keg is empty and needs replacing. Inspect the air and dispenser lines for any kinks, obstructions, or freezing. Finally, verify that all connections are secure and that all seals are in place and in good condition.
  • M
    Mary SantosAug 17, 2025
    How to fix too much foam in Insignia Beverage Dispenser?
    • C
      Cody AllenAug 17, 2025
      Excessive foam in your Insignia Beverage Dispenser can stem from several causes. If the keg was recently moved, let it sit for at least two hours before tapping. Ensure the CO₂ pressure reads between 10 and 12 PSI. The kegerator should cool to the high 30s to mid 40s. If the beer keg has been exposed to a warm environment, allow sufficient cooling time. You can also activate the pressure relief valve on the keg coupler for three seconds.
  • J
    Jonathan DanielAug 21, 2025
    What to do if Insignia NS-BK2TSS6 has sputtering draw?
    • A
      Angel SantiagoAug 21, 2025
      If your Insignia Beverage Dispenser is dispensing beer with a sputtering draw, it could be due to a few reasons. The system may need cleaning. Also, check the seal between the keg and the faucet to ensure the keg tap is installed correctly. Make sure there are no obstructions in either the air line or dispenser line, and that neither are frozen. Finally, consider whether you are using the correct dispensing technique.
  • S
    Stephen PotterAug 25, 2025
    Why is the beer from my Insignia Beverage Dispenser flat?
    • J
      Jessica CalderonAug 26, 2025
      Flat beer from your Insignia Beverage Dispenser can result from several issues. Ensure you're using the correct dispensing technique. Verify that the CO₂ pressure is between 10 and 12 PSI. Make sure your glassware is clean. Also, check that the dispensing hose isn't too long; a shorter hose may be needed.
  • P
    Pamela MackAug 28, 2025
    How to stop the Insignia Beverage Dispenser faucet from dripping?
    • C
      Cynthia HernandezAug 29, 2025
      If the faucet on your Insignia Beverage Dispenser is dripping, ensure that the handle is fully returned to the off position after each pour.
  • J
    Joshua JacksonSep 1, 2025
    What causes abnormal taste in Insignia NS-BK2TSS6 Beverage Dispenser?
    • D
      dnicholsonSep 1, 2025
      If your Insignia Beverage Dispenser has an abnormal beer taste or smell, check the hoses for possible air leaks and replace the beer keg with a fresh one if the beer has exceeded its shelf life.
  • R
    Rebecca PopeSep 5, 2025
    What to do if having difficulty manipulating Insignia NS-BK2TSS6 Beverage Dispenser faucet handle?
    • L
      Linda HallSep 5, 2025
      If you're experiencing difficulty manipulating the faucet handle on your Insignia Beverage Dispenser, remove the faucet handle and connector nuts and inspect for possible damage.
  • K
    Katherine LambertSep 9, 2025
    Why is my Insignia Beverage Dispenser CO₂ tank discharging rapidly?
    • M
      Mr. Alexander FreemanSep 9, 2025
      If your Insignia Beverage Dispenser's CO₂ tank is discharging rapidly, ensure all lines are properly connected and check the air line for possible leaks.

Summary

Introduction

Important Safety Instructions

Critical safety guidelines and warnings for operating the kegerator/beverage cooler.

Important Safety Instructions

Grounding Requirement

Ensuring proper electrical grounding to prevent shock and fire hazards.

Locating Your Kegerator;Beverage Cooler

Before Using Your Kegerator;Beverage Cooler

Finding a Suitable Location

Detailed criteria for choosing an appropriate and safe location for the unit.

Providing a Proper Power Supply

Assembly Instructions

Installing the Casters (Optional)

Installing the Draft Arm Assembly

CO2 Regulator and Tank Installation

Attach the CO2 Tank

Options and steps for securing the CO2 tank inside or on the back of the unit.

Installing and Setting Up a Beer Keg

Installing the Keg Coupler

Procedure for attaching the keg coupler to the beer keg.

Adjusting the CO2 Regulator

How to set the correct CO2 pressure for optimal beer dispensing.

Using Your Kegerator;Beverage Cooler

Setting the Temperature

Dispensing Beer

Proper technique for pouring a beer with optimal foam head.

Troubleshooting - Beer Quality

Troubleshooting - Cooler Operation

Insignia NS-BK2TSS6 Specifications

General IconGeneral
BrandInsignia
ModelNS-BK2TSS6
Adjustable ShelvesYes
Reversible DoorYes
Interior LightYes
ColorStainless Steel
Power SourceElectric
Voltage120V
Beverage CapacityUp to 60 cans
Temperature Range35°F to 50°F
Cord Length6 ft.

Related product manuals