EasyManuals Logo

Insignia NS-RMTLG17 User Manual

Insignia NS-RMTLG17
6 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
V1 ENGLISH 17-0214
Before using your new product, please read these instructions to
prevent any damage.
QUICK SETUP GUIDE
Replacement
Remote
Control
For LG TVs
NSRMTLG17
PACKAGE CONTENTS
Replacement Remote Control for LG TVs
Quick Setup Guide
INSTALLING BATTERIES
Insert two AAA batteries (not included) into the
remote. Make sure that
the + and – symbols
match the + and –
symbols in the battery
compartment.
Note: To set up your
remote, follow the setup
steps below, in order, and STOP as soon as your remote
works correctly.
SETTING UP YOUR REMOTE
Your remote should work with most newer LG TVs
without requiring any setup. After you install the
batteries, test your remote. If the buttons work correctly,
your remote is ready to use and you do not need to do
any further setup.
If the buttons do not work, complete the following
steps:
1 Make sure that your TV is on and not in standby mode.
2 On your remote, press and hold the red and blue
buttons until the POWER button blinks twice.
3 Point your remote towards the TV, then press and hold
POWER until your TV turns o. As soon as your TV
turns o, immediately release the button. You have
three seconds to release the button before your
remote sends a dierent signal (code) to your TV. The
POWER button blinks twice.
4 Use your remote to turn on your TV, then test the other
buttons. If the buttons work, your remote is ready to
use.
If some of the buttons still do not work, complete the
following steps:
1 Make sure that your TV is on and not in standby mode.
2 On your remote, press and hold the red and blue
buttons until the POWER button blinks twice.
3 Point your remote towards your TV, then press and
hold one of the buttons (such as MENU) that is not
working correctly.
As soon as the correct function (in this example,
MENU) appears on your TV screen, immediately
release the button. The POWER button blinks twice.
You have three seconds to release the button before
your remote sends a dierent signal (code) to your TV.
4 Test the rest of the buttons. If the buttons work, your
remote is ready to use.
5 If some of the buttons still do not work, repeat the
above steps for another non-working button, then test
the rest of the buttons. Repeat until all the buttons
work.
LEARNING FUNCTIONS
Your remote can learn any function from your original
remote as long as the original remote works.
1 Place both remotes on a at surface with the infrared
eyes facing each other.
Note: If you have diculty with the learning function, install
new batteries in both remotes and try the process again.
Make sure that the remote control eyes are pointing at
each other and are 1-2 inches apart.
2 On your new remote, press and hold the green and
yellow buttons until the POWER button blinks twice.
3 On your new remote, press 975. The POWER button
blinks twice.
4 On your new remote, press the button you want to
learn a new function (for example, VOL+).
5 On the original remote control, press the button with
the function you want to teach to the button you
pressed in step 4.
If the
POWER button blinks twice, your new remote
learned the function. You can repeat steps 4 and 5 to
add another function to your new remote.
If the
POWER button blinks one long blink, your new
remote did not learn the function. Repeat steps 4 and 5.
6 After you teach your new remote all the functions
you want it to learn, press and hold OK for three
seconds until the POWER button blinks twice.
DELETING A LEARNED FUNCTION
1 Press and hold the green and yellow buttons until
the POWER button blinks twice.
2 Press 976.
3 Press the button you want to reset twice
(for example, VOL+). The POWER button blinks
twice and the button is reset to its original function.
TROUBLESHOOTING
POWER button does not blink when a button is
pressed.
Replace the batteries.
LEGAL NOTICES
FCC Statement:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning
the equipment o and on, the
user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and
receiver.
—Connect the equipment into an outlet on a circuit
dierent from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
Caution: Changes or modications not expressly
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
ONEYEAR LIMITED WARRANTY
Visit www.insigniaproducts.com for details.
CONTACT INSIGNIA:
For customer service, call1-877-467-4289
www.insigniaproducts.com
INSIGNIA is a trademark of Best Buy and its aliated companies
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave South, Richeld, MN 55423 U.S.A.
©2017 Best Buy. All rights reserved
Made in China
2 X AAA
1-2 in.
Original remote
New remote
NS-RMTLG17_17-0214_QSG_V1_EN_SP_Final.ai 1 4/17/2017 3:31:58 PM

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Insignia NS-RMTLG17 and is the answer not in the manual?

Insignia NS-RMTLG17 Specifications

General IconGeneral
BrandInsignia
ModelNS-RMTLG17
CategoryRemote Control
LanguageEnglish

Related product manuals