What to do if my InSinkErator FAUCET has no warm water?
If your InSinkErator Plumbing Product isn't providing warm water, ensure the unit is plugged into a properly grounded electric outlet. Also, check that the circuit breaker or fuses are functioning correctly and that the outlet is not switched off.
Why is my InSinkErator FAUCET dripping from the spout/vent constantly?
Constant dripping from the spout/vent of your InSinkErator Plumbing Product is often due to debris in the water line, which may be lodged in the faucet valve seat, causing a slow leak. To resolve this, unscrew the spout end piece and clean out any debris. Additionally, lift the faucet lever 7-10 times to flush the faucet and lines.
What to do if my InSinkErator Plumbing Product is dripping from the spout/vent intermittently?
If your InSinkErator Plumbing Product drips intermittently, it could be due to the expansion chamber not draining properly because of low water pressure, or a blocked spout. First, unplug the unit. If dripping continues, check that the supply valve is fully open and there are no obstructions in the water line reducing the pressure below 30 psi. Also, unscrew the spout end piece and clean out any debris.
Why does water and steam spit forcefully from my InSinkErator Plumbing Product?
If water and steam spit forcefully from the spout of your InSinkErator Plumbing Product without turning on the faucet, it may be because the water is boiling in the storage tank. This can be normal during the initial setup. To resolve this, lift the faucet lever to release some water from the tank and adjust the water temperature down using the dial on the tank front. Remember that at higher altitudes, water boils at lower temperatures.
How to fix a divided stream from my InSinkErator FAUCET Plumbing Product?
A divided stream from your InSinkErator Plumbing Product is likely caused by debris in the end piece. To fix this, unscrew the spout end piece and clean out any debris.
Why is the water from my InSinkErator Plumbing Product too hot or not warm enough?
If the water from your InSinkErator Plumbing Product is too hot or not warm enough, the thermostat may not be adjusted to your needs. Adjust the thermostat slowly, then lift the faucet handle for 20 seconds to bring in fresh water to be heated at the new setting. Allow 5-7 minutes for the water to reach the new temperature.
What to do if water comes out the vent instead of the spout on my InSinkErator Plumbing Product?
If water is coming out of the vent instead of the spout on your InSinkErator Plumbing Product, it indicates that the outlet tube is blocked. Check that the outlet tube is not kinked, twisted, or pinched. Additionally, unscrew the spout end piece and clean out any debris.
Essential safety and usage instructions before installing or using the hot water faucet.
Lists required and recommended equipment for the installation process.
Details all the parts included with the InSinkErator faucet system.
Explains the manual's structure, including sections, subheadings, and visual cues.
Defines DANGER, WARNING, and CAUTION levels for hazardous situations.
Covers initial checks like location, clearance, counter thickness, and electrical outlet.
Step-by-step guide for assembling and mounting the faucet onto the sink or countertop.
Instructions for securely mounting the hot water tank under the sink.
Details on how to connect the faucet's water lines to the tank using fittings.
Guidance on connecting the unit to the cold water supply, recommending a shutoff valve.
Steps to fill the tank with water and connect the unit to electrical power.
Details the 1-year warranty coverage, exclusions, and service contact information.
Lists common problems, possible causes, and recommended solutions for the faucet system.
Instructions on how to adjust the tank temperature for desired output water temperature.
Procedure for unplugging and draining the unit for extended periods or freezing temperatures.
Recommendations for cleaning the faucet and plastic components to avoid damage.
General| Category | Plumbing Product |
|---|---|
| Brand | InSinkErator |
| Type | Faucet |
| Dimensions | Varies by model |
| Finish | Chrome |
| Installation | Deck Mount |
| Material | Varies by model (e.g., Brass, Stainless Steel) |
To Next Page
