Why is my InSinkErator Dispenser water not hot?
If your InSinkErator Dispenser isn't providing hot water, first ensure the unit is properly plugged into a grounded electrical outlet. Check that the circuit breaker or fuses are functioning correctly and that the outlet isn't switched off.
Why is my InSinkErator Invite H770-SS spitting water and steam?
If water and steam are forcefully spitting from the spout of your InSinkErator Dispenser without the faucet being turned on, the unit may be boiling, which can be normal during the initial setup. Activate the faucet lever to release some water from the tank. You can also adjust the water temperature using the dial on the front of the tank, keeping in mind that water boils at lower temperatures at higher altitudes.
Why is my InSinkErator Invite H770-SS Dispenser dripping constantly?
If your InSinkErator Dispenser is constantly dripping, the issue may be due to debris in the water line affecting the faucet valve seat. Try unscrewing the spout end piece to clean out any debris. Additionally, activate the faucet lever 7-10 times to flush the faucet and lines.
How to adjust the water temperature on my InSinkErator Invite H770-SS Dispenser?
If the water from your InSinkErator Dispenser is either too hot or not hot enough, the thermostat may need adjustment. Adjust the thermostat slowly, then activate the faucet lever for about 20 seconds to introduce fresh water for heating at the new setting. Allow approximately 5-7 minutes for the water to reach the new temperature.
What to do if my InSinkErator Invite H770-SS is dripping intermittently?
If your InSinkErator Dispenser is dripping intermittently, it could be due to a blocked spout or the expansion chamber not draining properly because of low water pressure. First, unplug the unit. If dripping persists, check the supply valve to ensure it's fully open and that there are no obstructions reducing the pressure below 30 psi. Also, unscrew the spout end piece and clean out any debris.
Why is water coming out of the vent of my InSinkErator Invite H770-SS Dispenser?
If water is coming out of the vent instead of the spout on your InSinkErator Dispenser, the outlet tube may be blocked. Check that the outlet tube isn't kinked, twisted, or pinched. Additionally, unscrew the spout end piece and clean out any debris.
Why is my InSinkErator Invite H770-SS Dispenser stream divided?
If you're experiencing a divided stream from your InSinkErator Dispenser, there may be debris in the end piece. Try unscrewing the spout end piece and cleaning out any debris.
Why does my InSinkErator Invite H770-SS keep running after I release the lever?
If water continues to run from your InSinkErator Dispenser after releasing the lever (models HC3/GN3/View/Wave), the mounting nut may be too tight, or the mounting washers may not be installed correctly. Try loosening the mounting nut, a 1/4 turn at a time, until shut-off occurs. Check the mounting washer installation.
Covers options for sinks without a sprayer hole or when not using it.
Unpacking the dispenser and straightening copper tubing for installation.
Steps for feeding tubes through sink holes with standard and larger diameters.
Attaching washers, star nut, and securing the dispenser head.
Procedure for installing faucet into holes smaller than 1½ inches using specific parts.
Unpacking the dispenser and straightening copper tubing for installation.
Details on washer placement for 1¼-inch and larger sink holes.
Feeding tubes through the sink and tightening the assembly with a wing nut.
Attaching quick connector and installing the white 3/8" tube for HC3 models.
Unpacking the dispenser and straightening copper tubing for installation.
Ensuring the rubber gasket is seated properly for a secure seal.
Mounting the dispenser using the semi-circular plate and wing nut.
Unpacking the dispenser and straightening copper tubing for installation.
Ensuring the fiber gasket is seated properly for a secure seal.
Feeding tubes through the sink and positioning the faucet head.
Using the mounting plate and screw to secure the dispenser base.
Choosing a suitable under-sink spot for vertical tank mounting.
Instructions for pre-drilling, hanging, and tightening the tank screws.
Attaching the snap-connect fitting to the blue 1/4" tube and tank fitting.
Connecting the white 7/16" and clear 5/16" tubes to the tank fittings.
Installing T-fitting, control valve, and connecting white 3/8" tube.
Installing T-fitting, control valve, and connecting copper 1/4" tube.
Turning on water, depressing hot handle to flush lines and fill tank.
Checking connections, plugging in, and allowing water to reach target temperature.
Instructions for resetting and adjusting the unit's temperature setting.
Procedure for unplugging, draining, and storing the unit during extended periods.
Recommendations for cleaning dispenser components to maintain performance.
Addresses forceful spitting from the spout without faucet activation.
Troubleshooting for water not being hot enough or being too hot.
Resolving issues like water from the vent, dripping, or divided stream.
Diagnosing and fixing the problem of water running after lever release.
Capacity| water capacity | 2/3-gallon |
|---|---|
| water dispensed per hour | 60 cups |
Power| voltage | 115 volts A.C. |
|---|---|
| power consumption | 750 watts |
| current | 6.25 amps |
Operating Environment| minimum thermostat temperature | 160°F |
|---|---|
| maximum thermostat temperature | 210°F |
| factory preset thermostat temperature | 200°F |
Weight and Dimensions| shipping weight | 7.4 lbs |
|---|---|
| minimum distance from sink hole center | 2" |
| counter thickness | 3/4" |
To Next Page
