Instek Digital LCR-819 User Manual

LCR-800 Series User Manual
i
CONTENTS PAGE
1. INTRODUCTION……………………………………..……... 1
2. PRECAUTIONS BEFORE OPERATION…….…………….
2-1.Unpacking the instrument………………….…………….
2-2.Checking the Line Voltage…………………..……………
2-3.Environment……………………………………..………..
2-4.Equipment Installation and Operation…………………
2
2
2
3
3
3. PANEL DESCRIPTION…...……………………..………….. 4
OPERATION…………….………………………………...….
4-1.Connects to DUT….………………..………….……..…...
4-2.Start-Up……….....……………………………..………….
4-3.Zeroing…………………………………………………….
4-4.Menu Functions.…..………………………………………
4-5.Measurement Conditions…..……………………………..
8
8
8
8
11
18
4.
5.
SPECIFICATIONS…………………………………………...
35
6. MESSAGE CODE.………………………………………….... 44
7. MAINTENANCE....…………………………………………...
7-1.Cleaning……………………………………………………
7-2.Battery Replacement……………………………………...
7-3.Recall Calibration………………………………………...
45
45
45
46
8. OPTION 1 (BIN Function for LCR-826/827/829 only)……..
8-1. BIN Functions for Components Sorting……………..….
8-2. BIN Setting Conditions.....……………………………….
8-3. BIN Range Setting: Component Sorting Range..............
48
48
50
56
9. OPTION 2……………………………………………………..
9-1.On-line procedure…………………………………………
9-2.RS232 VIEWER Software Operation…………………...
9-3.The Configuration of Cable………………………………
65
65
69
74
LCR-800 Series User Manual
ii
SAFETY TERMS AND SYMBOLS
These terms may appear in this manual or on the product:
WARNING: Warning statements identify condition or practices
that could result in injury or loss of life.
CAUTION: Caution statements identify conditions or practices
that could result in damage to this product or other property.
The following symbols may appear in this manual or on the product:
DANGER ATTENTION Protective Frame or Chassis
High Voltage refer to Manual Conductor Terminal
Terminal

Instek Digital LCR-819 Specifications

General

Type	Digital LCR Meter
Test Frequency	100Hz, 120Hz, 1kHz, 10kHz, 100kHz
Basic Accuracy	0.1%
Output Impedance	100Ω
Equivalent Circuit Mode	Series, Parallel
Frequency Range	100Hz to 100kHz
Accuracy	±0.1%
Test Signal Level	0.3Vrms, 1.0Vrms
Display	LCD with backlight
Measurement Parameters	L, C, R, D, Q, θ
Interfaces	USB, RS-232
Output Interface	USB
Measurement Speed	3 times per second
Power Supply	AC 100V to 240V, 50/60Hz

Summary

Safety Terms and Symbols

Precautions Before Operation

Operation

Basic Operation and Zeroing Procedures

Steps for connecting the DUT, starting up the instrument, and performing open/short circuit zeroing for accuracy.

Menu Functions and Measurement Settings

Overview of menu-driven functions, including parameter selection, measurement modes, and condition settings like frequency, voltage, and speed.

Specifications

Measurement Parameters and Display Ranges

Maintenance

Cleaning and Battery Replacement

Option 1: BIN Functions

BIN Functions for Component Sorting

Setup and usage of the BIN function for sorting components based on measurement criteria.

BIN Setting Conditions and Ranges

Option 2: RS-232C Communication

On-line Procedure

Steps to establish an on-line connection between the LCR meter and a computer using RS-232C.

RS232 VIEWER Software Operation