Integra DRX-2.1 User Manual

14
> Network Functions > Specifications > Advanced Setup > Listening Modes
Troubleshooting Supplementary Information, etc�|
> Basic Manual
■ 4� Level Calibration
Setting Item Default Value Setting Details
Front Left 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Center 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Front Right 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Height Left 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
•
The setting cannot be changed if "Zone 2" is set
in "Configuration" - "Zone Speaker" and Zone 2
is on.
Height Right 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
•
The setting cannot be changed if "Zone 2" is set
in "Configuration" - "Zone Speaker" and Zone 2
is on.
Surround Right 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Setting Item Default Value Setting Details
Surr Back Right 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
•
The setting cannot be changed if "Zone 2" is set
in "Configuration" - "Zone Speaker" and Zone 2
is on.
Surr Back Left 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
•
The setting cannot be changed if "Zone 2" is set
in "Configuration" - "Zone Speaker" and Zone 2
is on.
Surround Left 0 dB Select a value between "−12 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
Subwoofer 0 dB Select a value between "−15 dB" and "＋12 dB"
(in 1 dB increments). A test tone will be output
each time you change the value. Select the desired
level.
■ 5� Dolby Enabled Speaker
Setting Item Default Value Setting Details
Dolby Enabled
Speaker to
Ceiling
6.0 ft/1.80 m Set the distance between the Dolby Enabled
Speaker and the ceiling. Select between "0.1
ft/0.03 m" to "15.0 ft/4.50 m" (0.1 ft/0.03 m units).
•
The unit of distance (ft/m) shown is the unit
selected for use in "Distance".
AccuReflex Off You can enhance the reflection effect of Dolby
Enabled Speakers from the ceiling.
"Off": When this function is not to be used
"On": When this function is to be used
•
This setting can be selected when "Configuration" - "Height Speaker" is set to "Dolby Speaker".

Integra DRX-2.1 Specifications

General

Brand	Integra
Model	DRX-2.1
Category	Stereo Receiver
Language	English