intensity Dual Channel TENS User Manual (English)

Questions and Answers:

M
mrogersAug 13, 2025
What to do if I cannot feel any stimulation from my intensity Dual Channel TENS?
- L
  Levi SweeneyAug 14, 2025
  If you're not feeling any stimulation from your Intensity Medical Equipment, it could be due to a few reasons. First, the electrodes might be dried out or dirty, in which case you should replace them. Another cause could be that the electrodes won't stick to your skin. If that happens, clean the treatment area to remove any dirt or oily substances like lotion. Also, old, worn, or damaged lead wires may cause this problem, so replacing them with new ones is a good idea.
B
Barry SullivanAug 17, 2025
How to fix intensity Dual Channel TENS Medical Equipment that cannot power on?
- T
  Tara Reeves DVMAug 17, 2025
  If your Intensity Medical Equipment isn't powering on, there are a couple of things to check. First, make sure the batteries aren't depleted; if they are, recharge or replace them. Also, ensure that the batteries are installed correctly, paying attention to the correct polarity when you insert them.
A
adam15Aug 21, 2025
Why is the stimulation from my Intensity Medical Equipment so uncomfortable?
- M
  Mrs. Maria MorganAug 21, 2025
  If the stimulation from your Intensity Medical Equipment feels uncomfortable, it might be because the intensity is set too high, so try decreasing it. Another reason could be that the electrodes are too close together; reposition them to be at least 1½" apart. Also, the electrode active area size might be too small. In that case, replace the electrodes with ones that have an active area no less than 25.0cm2 (5cm x 5cm). Finally, make sure you are operating the device according to the manual.
J
Joan GreenAug 25, 2025
What to do if the output current stops during therapy with my Intensity Medical Equipment?
- R
  Renee WestAug 26, 2025
  If the output current stops during therapy with your Intensity Medical Equipment, it could be because the electrode came off the skin or the edges are lifting away from the skin. Turn off the device and reapply the electrodes to your skin. It's also possible that the lead wires are disconnected, so turn off the device and reconnect the lead wires. Also, check if the batteries are depleted and charge or replace them if needed.
K
Kimberly WagnerAug 28, 2025
How to troubleshoot intermittent output on my Intensity Medical Equipment?
- D
  debbie00Aug 28, 2025
  If you're experiencing intermittent output with your Intensity Medical Equipment, first verify that the lead wire connection is secure. If that doesn't solve the problem, try turning down the intensity. You can also try rotating the lead wire in the socket 90º. If the issue continues, replace the lead wire.
P
Paula BrockSep 1, 2025
Why does my skin become red and/or I feel a stabbing pain when using my Intensity Medical Equipment?
- T
  Tyler PottsSep 1, 2025
  If your skin becomes red or you feel a stabbing pain while using your Intensity Medical Equipment, it could be because you're using the electrode on the same site every time. Try repositioning the electrode to another area. Stop use immediately if you feel pain or discomfort. It could also be that the electrode is not sticking onto the skin properly, so ensure the electrode is securely placed on the skin.
B
benjamin15Sep 5, 2025
What to do if my skin becomes red and/or I feel a stabbing pain while using my intensity Dual Channel TENS Medical Equipment?
- P
  Philip HallSep 5, 2025
  If your skin becomes red or you feel a stabbing pain while using your Intensity Medical Equipment, it might be because the electrode is dirty. Clean the electrodes or replace them with new ones. Another cause could be that the surface of the electrode is scratched, so replace it with a new one.
B
Brian NguyenSep 9, 2025
Why is the stimulation ineffective on my Intensity Medical Equipment?
- A
  Anthony WoodardSep 9, 2025
  If the stimulation from your Intensity Medical Equipment is ineffective, it may be due to improper electrode placement. Try repositioning the electrodes.

intensity Dual Channel TENS Specifications

General

Usage	Pain Relief, Muscle Stimulation
Portability	Portable
Pulse Rate	2-150 Hz
Intensity Levels	Adjustable
Battery Type	9V
Channels	Dual Channel
Output Voltage	Adjustable (typically up to 100V)