Interphone F3MC - Intercom Communication; Device Pairing Procedures; Pairing with INTERPHONE MC Units; Pairing with Non-MC Interphone Units

ENGLISH - 11 ENGLISH - 12
4.1.2 Pairing with an INTERPHONE unit (not MC).
With your unit in Standby mode (led BLUE (6) ashing):
1. Press once the UP (2) buon and then press once the MFB (1) buon to acvate
the “SETUP” menu.
2. Press three mes the UP (2) buon to select “INTERCOM DEVICE SEARCH” feature,
press the MFB (1) unl the beep to start the search.
3. On the second Interphone unit (previous series not “MC”), with unit o, push and
keep pressed the MFB buon unl the alternate ashing red/blue of unit led.
4. Aer few seconds the units will be paired, intercom connecon will be
automacally started (led BLUE (6) on). To stop the intercom communicaon press
once MFB (1) buon on one of the two units.
4.1.3 Pairing with units not Interphone (other brands)
With your unit in Standby mode (led BLUE (6) ashing):
1. Press once the UP (2) buon and then press once the MFB (1) buon to acvate
the “SETUP” menu.
2. Press four mes the UP (2) buon to select “ANYCOM SEARCH” feature, press the
MFB (1) unl the beep to start the search.
3. On the second unit NOT Interphone start the “phone search/phone pairing mode”,
see user manual of NOT Interphone unit for more details.
4. Aer few seconds the units will be paired, intercom connecon will be
automacally started (led BLUE (6) on). To stop the intercom communicaon press
once MFB (1) buon on your F3MC unit.
4.2 Intercom communicaon between two units (from “INTERCOM” menu)
To start an intercom communicaon between your F3MC (unit nr1 Pic. 4) and another
one (unit nr2 Pic. 4) follow these steps:
1. Pair units 1 and 2 (chapters 4.1.1/4.1.2/4.1.3), this is necessary only once.
2. With your F3MC unit in Standby mode (led BLUE (6) ashing), press once the MFB
(1) buon, connecon will be started. The vocal guidance will prompt a message for
intercom acvaon, BLUE (6) led of F3MC units will lights up. To stop the intercom
communicaon press once MFB (1) buon on your F3MC, both units will go in
Standby mode.
1 2
Pic.4
4 – Intercom
F3MC allows intercom communicaon (INTERCOM) in full duplex between rider and
passenger.
4.1 Pairing
Before starng the communicaon between headsets, is necessary to pair together the
units. This process has to be done only one me. F3MC will automacally recognize devices
previously paired.
F3MC is compable with all range of INTERPHONE device (also previous series) and by
ANYCOM funcon is also compable with other brands of helmet Bluetooth headsets.
Each F3MC can be paired to only one more unit.
If a F3MC unit has been paired with a unit, running a further pairing, with
another unit, will delete the pairing with rst one.
4.1.1 Pairing with an INTERPHONE MC unit
With both units in Standby mode (led BLUE (6) ashing):
1. On your F3MC unit press once the UP (2) buon and then press once the MFB (1)
buon to acvate the “SETUP” menu.
2. Press three mes the UP (2) buon to select “INTERCOM DEVICE SEARCH” feature,
press the MFB (1) unl the beep to start the search.
3. On the other unit F3MC press UP (2) buon and then press once MFB (1) buon to
acvate the “SETUP” menu.
4. Press UP (2) buon two mes, the second MC unit will go in “PAIRING MODE”.
5. Aer few seconds the units will be paired, intercom connecon will be automacally
started (led BLUE (6) on). To stop the intercom communicaon press once MFB (1)
buon on one of the two units.