To Next PageTo Next PageHow to fix an Intex 128474GN Hot Tub that loses air pressure?
If your Intex Hot Tub is losing air pressure, start by checking the air valve cap to ensure it's securely closed. Also, make sure the air valve base is tightened; fill the spa tub with air first. If you find a hole, cut, or split on the spa tub, apply liquid soap and water to the seams to locate the leak. Clean and dry the area, then apply the repair patch included with your spa.
Why does my Intex Hot Tub keep tripping the household circuit breaker?
If the household circuit breaker trips when you use your Intex Hot Tub, it could be due to several reasons. First, ensure that the circuit breaker has the correct rating. If it's underrated, it may trip easily. Also, the circuit breaker might be overloaded. To fix this, provide a dedicated circuit breaker that feeds only the spa's electrical outlet. If there's an electrical fault in the line, contact a qualified electrician to correct it.
How to fix an Intex 128474GN that is not heating properly?
If your Intex Hot Tub isn't heating properly, start by increasing the set temperature and ensuring the spa cover is attached to retain heat. A dirty filter cartridge can also cause heating issues, so clean or replace it promptly. If the heater is in STANDBY mode, press the flame button twice to heat the water to the set temperature. If the heating element has failed, contact the Intex Service Center.
How to fix Intex 128474GN Hot Tub that loses air pressure?
If your Intex Hot Tub tub loses air pressure, first, ensure the air valve cap is securely closed. If that doesn't solve the problem, fill the tub with air and tighten the air valve base. To find any leaks, apply soapy water to the seams; bubbles will indicate a leak. Clean and dry the area before applying the repair patch included with your spa.
How to clean Intex 128474GN Hot Tub water?
To clean your Intex Hot Tub water, ensure the cartridge assembly is properly attached. Increase the filtration time. Regularly clean or replace the filter cartridge. Maintain proper water sanitation by following the chemical manufacturer’s instructions. Also, check and clean the filtration inlet and outlet regularly.
What to do if the filtration pump on my Intex 128474GN Hot Tub is not working?
If the filtration pump on your Intex Hot Tub isn't working, the first thing you should check is the filter cartridge. If it's dirty, clean or replace it. Also, inspect the filtration inlet and outlet for any clogs and clean them regularly. If the filter pump motor has failed, contact the Intex Service Center.
How to level Intex Hot Tub pump connectors?
To level the pump connectors on your Intex Hot Tub with the spa connectors, elevate the pump using wood or another type of insulated material.
What to do if my Intex Hot Tub has no display or the control unit doesn't work?
If the Intex Hot Tub control unit isn't working or displaying anything, first, make sure the spa is properly plugged in and switched on. Then, check that the control panel cable is firmly connected to the control base. Also, verify the power source and reset the RCD if it has tripped. If the RCD is broken, you should contact the Intex Service Center.
Why Intex Hot Tub display is not working?
If the display or spa control unit on your Intex Hot Tub isn't working, make sure the spa is plugged in and switched on. Check that the control panel cable plug is firmly attached to the control base receptacle. Verify the power source and reset the RCD. The RCD might be broken.
What to do if the water in my Intex Hot Tub is not clean?
If the water in your Intex Hot Tub isn't clean, several factors could be responsible. Make sure the cartridge assembly is properly attached. Increase the filtration time to allow for more thorough cleaning. Regularly clean or replace the filter cartridge. Maintain proper water sanitation by following the chemical manufacturer’s instructions. Also, check and clean the filtration inlet and outlet to ensure they are free from clogs.
General