Intex PureSpa SSP-H-20-1 User Manual (English)

Questions and Answers:

D
Danielle DillonAug 20, 2025
Why does my Intex PureSpa SSP-H-20-1 Hot Tub keep tripping the household circuit breaker?
- M
  myersbrianAug 20, 2025
  If your Intex Hot Tub is tripping the household circuit breaker, it could be due to several reasons: * The circuit breaker may be under-rated; ensure it has the correct rating. * The circuit breaker might be overloaded; provide a dedicated circuit breaker feeding the spa electrical outlet only. * There may be an electrical fault in the line; contact a qualified electrician to correct the electrical fault.
J
John BallAug 21, 2025
Why does my Intex PureSpa SSP-H-20-1 keep tripping the circuit breaker?
- K
  Kelly FisherAug 22, 2025
  Your Intex Hot Tub might be tripping the circuit breaker because the circuit breaker is underrated or overloaded, or there could be an electrical fault. Ensure you have the correct circuit breaker rating and a dedicated circuit for the spa. If there's an electrical fault, contact a qualified electrician.
J
Joe BrownAug 25, 2025
How to fix Intex Hot Tub not heating properly?
- J
  Jamie ShafferAug 25, 2025
  If your Intex Hot Tub isn't heating properly, try these steps: increase the temperature setting and ensure the spa cover is attached. Clean or replace the filter cartridge. If the heater is in STANDBY mode, press the flame button twice. The heating element might have failed.
L
Leslie WalterAug 26, 2025
How to fix an Intex PureSpa SSP-H-20-1 that is not heating properly?
- W
  Wendy RoseAug 26, 2025
  If your Intex Hot Tub isn't heating properly, consider the following: * Increase the set temperature and ensure the spa cover is attached. * Clean or replace the filter cartridge in time. * If the heater is in STANDBY mode, press the flame button twice to heat the water to the set temperature. * If the heating element has failed, contact Intex Service Center.
M
Michael JimenezAug 28, 2025
How to clean cloudy water in Intex Hot Tub?
- J
  Joshua DavisAug 28, 2025
  To address cloudy water in your Intex Hot Tub, ensure the cartridge assembly is properly attached and increase filtration time. Clean or replace the filter cartridge and maintain proper water sanitation. Check and clean the filtration inlet and outlet regularly.
R
Richard YoungAug 29, 2025
Why is my Intex PureSpa SSP-H-20-1 Hot Tub losing air pressure?
- J
  Joan HortonAug 29, 2025
  Your Intex Hot Tub might be losing air pressure because the air valve cap or base is loose, or there's a hole, cut, or split in the spa tub. Ensure the air valve cap is securely closed and tighten the air valve base. To find a leak, apply soapy water to the seams; bubbles will indicate the leak's location. Clean and dry the area before applying the repair patch.
C
Christina DavisAug 31, 2025
What to do if my Intex Hot Tub control unit does not work?
- L
  Lori StricklandAug 31, 2025
  If the control unit of your Intex Hot Tub isn't working, there are several things to check: * Ensure the spa is plugged in and switched on. * Verify the control panel cable plug is firmly attached to the control base receptacle. * Check your power source. * Reset the RCD (Residual Current Device). If the RCD is broken, contact Intex Service Center.
M
Melissa KimSep 2, 2025
What to do if the bubble air blower on my Intex Hot Tub does not work?
- R
  Randy ReidSep 2, 2025
  If the bubble air blower on your Intex Hot Tub isn't working, it might be too hot. Turn off and unplug the spa, let it cool down, and then restart it. If the problem persists, contact Intex Service Center.
J
Joseph BryantSep 4, 2025
What to do if my Intex PureSpa SSP-H-20-1 display is not working?
- R
  Richard WilsonSep 5, 2025
  If the display of your Intex Hot Tub isn't working, first, ensure the spa is plugged in and switched on, and that the control panel cable is firmly attached to the control base. Check the power source and reset the RCD. If the problem persists, it may indicate a broken RCD.
B
Brian DavilaSep 7, 2025
What to do if the Intex Hot Tub filtration pump is not working?
- C
  Carlos HuertaSep 7, 2025
  If the filtration pump of your Intex Hot Tub isn't working, clean or replace the filter cartridge. Also, check and clean the filtration inlet and outlet regularly.

Intex PureSpa SSP-H-20-1 Specifications

General

Model	SSP-H-20-1
Type	Inflatable Hot Tub
Air Jets	140 high-powered bubble jets
Water Capacity	210 gallons
Temperature Range	Up to 104°F
Inflation System	Built-in inflation system
Included Accessories	Insulated cover, carry bag