To Next PageTo Next PageHow to stop Intex PureSpa SB-HSWF10 from leaking at connectors?
If there's leaking between the spa tub and control unit connectors on your Intex Hot Tub, tighten the inlet and outlet connections. Coat the O-ring with petroleum jelly for a waterproof seal. Remove the grid from inside the spa with a screwdriver, and ensure the inlet/outlet O-ring is in place, clean, and undamaged.
What to do if my Intex Hot Tub keeps tripping the circuit breaker?
If the household circuit breaker trips when using your Intex Hot Tub, ensure the circuit breaker has the correct rating. Provide a dedicated circuit breaker feeding only the spa's electrical outlet. If tripping continues, contact a qualified electrician to correct the electrical fault.
What does error code E90 mean on my Intex PureSpa SB-HSWF10 Hot Tub?
If your Intex Hot Tub displays error code E90, turn off and unplug the control unit. Ensure the outlet cover grid is clean and free of obstructions. Clean or replace the cartridge. Make sure the inlet/outlet connections on the spa tub and filter pump are not blocked. Keep the spa water properly sanitized. Plug the GFCI/RCD and restart. If the problem persists, contact Intex Service Center.
What does error code E91 mean on my Intex PureSpa SB-HSWF10 Hot Tub?
If your Intex Hot Tub displays error code E91, remove the electrolytic cell for inspection and clean it if necessary. Add salt. Ensure that the cell cord is plugged firmly into the cell receptacle. If the problem persists, contact Intex Service Center and consider replacing the cell.
How to fix insufficient chlorine in Intex PureSpa SB-HSWF10?
If there's insufficient chlorine in your Intex Hot Tub, increase the sanitation system operating time, ensuring the heater is off during sanitation. Use a spa cover when the spa is not in use or when the sanitation system is operating. Increase sanitation time and test the water. Check and clean the electrolytic cell if needed.
What does error E92 mean on my Intex Hot Tub?
If your Intex Hot Tub displays error code E92, partially drain the pool and refill it with fresh water. If the problem persists, contact Intex Service Center.
Why is air pressure weak when inflating my Intex PureSpa SB-HSWF10?
If the air pressure is weak when inflating your Intex Hot Tub, ensure the O-ring is in place on the hose adapter. Tighten or reinstall the hose adapter. Finger-tighten connections during inflation. If the problem persists, contact Intex Service Center.
Why are the air bubbles weak in my Intex PureSpa SB-HSWF10?
If the air bubbles in your Intex Hot Tub are weaker than before, ensure the O-ring is in place between the control base air outlet and spa tub air inlet connections. Finger-tighten all nuts. Repair any punctures with a repair patch. If the problem continues, contact Intex Service Center.
How to fix air leak in Intex Hot Tub?
If your Intex Hot Tub is losing air pressure, ensure the air valve cap is securely closed. Fill the tub with air and tighten the air valve base. To locate a leak, apply soapy water to the seams; bubbling indicates a leak. Clean, dry, and apply the provided repair patch to any leaks. Always turn the air passage selection dial to the correct position after inflation to prevent air escape.
How to fix no display on my Intex PureSpa SB-HSWF10 Hot Tub?
If the Intex Hot Tub display isn't working, first ensure the spa is plugged in and switched on, and that the control panel cable is firmly attached. Check the power source and reset the GFCI/RCD. If problems persist, contact Intex Service Center.
General| Model | SB-HSWF10 |
|---|---|
| Category | Hot Tub |
| Height | 28 inches |
| Temperature Range | 68-104°F |
| Capacity | 4 people |
| Outer Diameter | 77 inches |
| Temperature Increase Rate | 1-2°F/hour |
| Air Jets | 120 |
| Control Panel | Digital |
| Included Accessories | Insulated cover |
| Weight | 88 lbs |
Critical hazard warnings covering drowning, injury, electric shock, and health risks.
GFCI/RCD testing, water chemistry caution, and general safety notes.
Visual guide to identify all spa components by number.
Instructions for proper use and replacement of spa suction fittings.
Spa dimensions, capacity, power, temperature, and RF information.
Guidelines for spa placement, charging, and control panel setup.
Detailed steps for inflating the spa cover's air bladder.
Inflating the tub wall and procedures for adding air.
Deflating air, attaching accessories, and filling with water.
Steps for installing the foam cover and notes on air pressure release.
How the saltwater system works, salt types, and levels.
Overview of buttons, LED display, and temperature warning.
Using the Heat button, HST, and HDT for temperature control.
Toggling units, WiFi pairing, and LED indicator status.
Steps for installing the app, pairing, and understanding WiFi status.
Scenarios for using heater timers and settings.
How the LED display shows different operational data.
Procedures for activating the system, setting hours, and testing water.
Meanings and potential solutions for LED error codes.
Practices for maintaining clean, sanitized spa water.
Ideal readings for Free Chlorine, pH, Total Alkalinity, and Calcium Hardness.
Using chemicals to lower alkalinity and adjust pH levels.
Procedures for lowering or raising calcium hardness.
Inspecting, cleaning filter cartridges, and spa water maintenance.
Step-by-step guide for cleaning the electrolytic cell.
Instructions for testing water chemistry using provided test strips.
Procedures for emptying and cleaning the spa tub interior.
How to tighten the spa tub air valve if it leaks.
Inspecting the cover, locking buckles, and repairing punctures.
Steps for draining, cleaning, and storing the spa indoors.
Solutions for issues like no display, breaker trips, and heating.
Troubleshooting air leaks, connector issues, and water clarity.
Explanations and solutions for specific LED panel error codes.
Common problems and solutions during initial WiFi app setup.
Troubleshooting connectivity, app loading, and network interference.
Step-by-step guide for disassembling the filter pump motor.
Details on the PureSpa limited warranty, coverage, and claims.
