To Next PageTo Next PageWhy does my Intex Hot Tub keep tripping the circuit breaker?
If your Intex Hot Tub is tripping the household circuit breaker, make sure the circuit breaker has the correct rating. Provide a dedicated circuit breaker solely for the spa's electrical outlet. If the issue continues, contact a qualified electrician to fix the electrical fault.
How to fix an Intex PureSpa Greywood Deluxe SB-HWF10 that is not heating properly?
If your Intex Hot Tub isn't heating properly, first, increase the set temperature and ensure the spa cover is attached. Clean or replace the filter cartridge. If the heater is in standby mode, press the flame button twice to heat the water. If the issue persists, contact Intex Service Center.
What to do if the Intex PureSpa Greywood Deluxe SB-HWF10 Hot Tub water is not clean?
If your Intex Hot Tub water isn't clean, ensure the cartridge assembly is properly attached and increase filtration time. Regularly clean or replace the filter cartridge and maintain proper water sanitation, following the chemical manufacturer's instructions. Also, check and clean the filtration inlet and outlet.
Why are the air bubbles not as strong as before in my Intex PureSpa Greywood Deluxe SB-HWF10 Hot Tub?
If the air bubbles in your Intex Hot Tub are not as strong as before, check that the O-ring is in place between the control base air outlet and spa tub air inlet connections, and ensure the air connection nut is securely tightened. If there is any puncture, use a repair patch. If the problem continues, contact Intex Service Center.
How to fix an Intex Hot Tub that loses air pressure?
If your Intex Hot Tub tub loses air pressure, ensure the air valve cap is securely closed. Fill the tub with air and tighten the air valve base. Apply soapy water to the seams to check for leaks and use a repair patch if needed.
What to do if the Intex Hot Tub display is not working?
To resolve a non-working display or spa control unit on your Intex Hot Tub: Ensure the spa is plugged in and switched on, and that the control panel cable is firmly attached. Check the power source and reset the GFCI/RCD. If problems persist, contact Intex Service Center.
Why is the filtration pump not working on my Intex Hot Tub?
If the Intex Hot Tub filtration pump isn't working, clean or replace the filter cartridge. Check and regularly clean the filtration inlet and outlet. If the problem persists, contact Intex Service Center.
Why is the air pressure weak when inflating my Intex Hot Tub?
If the air pressure is weak during inflation of your Intex Hot Tub, check that the hose adapter o-ring is in place and that the inflation hose adapter is tightened securely. Ensure connections between the hose adapter and blower inflation outlet, and between the inflation hose and inflation valve, are not loose. If the problem persists, contact Intex Service Center.
What to do if the Intex Hot Tub bubble air blower does not work?
If your Intex Hot Tub bubble air blower isn't working, turn off and unplug the spa. Allow it to cool down, then restart. If the problem remains, contact Intex Service Center.
What causes leaking between Intex PureSpa Greywood Deluxe SB-HWF10 Hot Tub connectors?
If there's a leak between the spa tub and control unit connectors on your Intex Hot Tub, tighten the inlet and outlet connections. Coat the O-ring with petroleum jelly for a waterproof seal. Remove the grid inside the spa with a screwdriver to ensure the inlet/outlet O-ring is in place, clean, and undamaged.
General| Model | SB-HWF10 |
|---|---|
| Category | Hot Tub |
| Type | Inflatable |
| Water Capacity | 210 gallons |
| Material | PVC |
| Height | 28 inches |
| Temperature Increase | 1-2°F per hour |
| Control System | Digital Control Panel |
| Water Capacity (Litres) | 795 litres |
| Outer Diameter | 77 inches |
| Temperature Range | 68°F to 104°F |
| Voltage | 120V |
| Included Accessories | Cover, Filter |
Details on installing and maintaining spa suction fittings for optimal performance and safety.
Compliance information regarding FCC radiation exposure limits for uncontrolled environments.
Guidelines for selecting a location and preparing the site for spa installation, including indoor/outdoor needs.
Step-by-step instructions for inflating the spa tub wall and cover air bladder using the provided equipment.
Procedure for deflating the spa tub wall and cover air bladder for storage or disassembly.
Guidance on connecting the spa control unit to the spa tub and securing its components.
Explanation of control panel buttons, indicators, temperature settings, timer functions, and LED display.
Instructions for using the Heat, Heater Start Timer (HST), and Heater Duration Timer (HDT) buttons.
Guide to connecting the spa to the Intex App, including WiFi pairing, router requirements, and sharing features.
Guidelines for maintaining clean spa water, including sanitation, filter cartridge maintenance, and cleaning procedures.
Recommended water chemistry levels and procedures for adjusting pH, alkalinity, and hardness.
Instructions for draining, cleaning the spa tub interior, and performing routine maintenance.
Guidance on air valve fastening, air bladder repair, and spa cover maintenance.
Solutions for issues like no display, control unit failure, and improper heating.
Troubleshooting for a non-functional air blower, filtration pump, or unclean water.
Resolving issues with air pressure loss, leaks, unusual noises, and weak air bubbles.
Solutions for WiFi pairing failures, app loading problems, and connectivity issues with the mobile device.
Checks for correct mobile device versions, operating systems, and network compatibility for app function.
Resolving offline status, WiFi signal failures, and addressing network interference.
