Intex PureSpa Greywood Deluxe User Manual (English)

Questions and Answers:

R
Ryan ReidAug 17, 2025
What to do if my Intex PureSpa Greywood Deluxe Hot Tub is not heating properly?
- B
  Brandon CrosbyAug 17, 2025
  If your Intex Hot Tub isn't heating correctly, there might be a few reasons. First, check that the temperature isn't set too low and that the spa cover is on. A dirty filter cartridge can also cause this, so clean or replace it. Also, if the heater is in STANDBY mode, press the flame button twice to heat up the water to the set temperature. If these steps don't resolve the issue, it could be due to a failed heating element.
A
Adam VelezAug 20, 2025
Why does my Intex Hot Tub keep tripping the household circuit breaker?
- B
  Bradley MurphyAug 20, 2025
  Your Intex Hot Tub might be tripping the household circuit breaker because the circuit breaker is underrated, the circuit is overloaded, or there's an electrical fault in the line. Ensure the correct circuit breaker rating and provide a dedicated circuit breaker feeding the spa electrical outlet only.
W
williamnealAug 22, 2025
Why is my Intex Hot Tub water not clean?
- J
  jhoodAug 23, 2025
  If the water in your Intex Hot Tub isn't clean, several factors could be responsible. Ensure the cartridge assembly is properly attached. Insufficient filtering time, a dirty filter cartridge, improper water maintenance, or clogged filtration inlet and outlet could also be the cause. Increase filtration time, clean or replace the filter cartridge, keep the spa water properly sanitized, and check/clean the filtration inlet and outlet regularly.
R
Robert RobinsonAug 26, 2025
What to do if the air pressure is weak during Intex PureSpa Greywood Deluxe inflation?
- J
  Jennifer HillAug 26, 2025
  If you're experiencing weak air pressure while inflating your Intex Hot Tub, check that the hose adaptor o-ring is in place and that the inflation hose adaptor is securely tightened. Also, ensure the connection between the hose adaptor and blower inflation outlet, and between the inflation hose and inflation valve are not loose. Air blower failure can also be the cause.
J
Joseph HurleyAug 28, 2025
What to do if my Intex Hot Tub loses air pressure?
- D
  Darryl WilliamsAug 28, 2025
  If your Intex Hot Tub is losing air pressure, first ensure the air valve cap is securely closed. Next, fill the tub with air and tighten the air valve base. If it continues, check for holes, cuts, or splits by applying soapy water to the seams; bubbling indicates a leak. Clean, dry, and apply the provided repair patch to any leaks you find.
L
Lisa RoyAug 30, 2025
Why are the air bubbles not as strong as before in my Intex PureSpa Greywood Deluxe Hot Tub?
- S
  sandra82Aug 31, 2025
  If the air bubbles in your Intex Hot Tub aren't as strong as before, ensure the o-ring is in place between the control base air outlet and spa tub air inlet connections and that the air connection nut is securely tight. Also, check for any punctures in the air bubble channel inside the tub and repair them with a patch. The air blower may also have failed.
W
watsongabrielaSep 2, 2025
What to do if my Intex Hot Tub filtration pump is not working?
- E
  Ethan CookSep 3, 2025
  If the filtration pump in your Intex Hot Tub isn't working, start by cleaning or replacing the filter cartridge. Also, check the filtration inlet and outlet for any clogs and clean them regularly. If these steps don't solve the problem, the filter pump motor may have failed.
D
dweaverSep 5, 2025
What to do if my Intex PureSpa Greywood Deluxe Hot Tub control unit does not work?
- J
  Julian ScottSep 5, 2025
  If the Intex Hot Tub control unit isn't working or there's no display, make sure the spa is plugged in and switched on. Check that the control panel cable plug is firmly attached to the control base receptacle. Also, check the power source and reset the RCD. It may also be due to power failure, or the RCD being broken.
M
matthew91Sep 8, 2025
What to do if my Intex Hot Tub is too noisy in filtration mode?
- D
  David SloanSep 8, 2025
  If your Intex Hot Tub is excessively noisy during filtration, ensure the control panel, back cover, and all inlet/outlet connections are securely connected. Also, check that the ground is level, firm, and smooth. If the problem persists, the spa filter motor may have failed.
J
Jason JohnsonSep 12, 2025
What causes leaking between spa tub connectors and control unit connectors on my Intex Hot Tub?
- A
  Alec GrimesSep 12, 2025
  Leaking between the spa tub connectors and control unit connectors on your Intex Hot Tub can be caused by spa control base inlet/outlet connections not being securely tight or the inlet/outlet o-ring being missing or dirty. Tighten the inlet and outlet connections. Coat the o-ring with petroleum jelly for water proof. Remove grid from inside spa with a screwdriver, ensure inlet/outlet O-ring is in place, clean and not damaged.

Intex PureSpa Greywood Deluxe Specifications

General

Seating Capacity	4-6 people
Dimensions	77 x 77 x 28 inches
Control Panel	Digital
LED Lighting	Yes
Water Filtration	2 filter cartridges
Power Supply	110-120V
Temperature Range	68-104°F
Heating Rate	1-2°F per hour
Included Accessories	inflation hose, carry bag
Bubble Jets	140 high-powered bubble jets