Invacare Birdie EVO User Manual (English)

Other manuals for Invacare Birdie EVO

User Manual36 pages

Mounting Instruction2 pages

Questions and Answers:

H
hdeanAug 22, 2025
What to do if the electric actuator fails on my Invacare Birdie EVO Lifting Systems?
- S
  Shelly JonesAug 22, 2025
  If the electric actuator on your Invacare Lifting Systems fails to lift or the legs don't open when you press the button, here are some things to check: * Make sure the hand control or actuator connector is properly connected. * Charge the batteries if they are low. * Ensure the RED emergency stop button is not pressed IN; rotate it CLOCKWISE until it pops out. * Verify the battery is correctly connected to the control unit. * Disconnect the power cord from the power outlet, if connected. If the connecting terminals are damaged or the boom/leg actuator is worn, you may need to replace the hand control, control unit, or actuator.
L
longchristopherSep 2, 2025
Why has the damping lessened on my Invacare Birdie EVO spreader bar?
- R
  Robert Howard DDSSep 2, 2025
  If the damping of the spreader bar has lessened or disappeared completely, the damper is damaged and needs to be replaced.
A
Amy CooperSep 1, 2025
What causes a noisy sound from the pivots of Invacare Birdie EVO Lifting Systems?
- J
  Joseph MitchellSep 1, 2025
  A noisy or dry sound from the pivots indicates that the pivots are worn or damaged. You will need to replace the pivots.
C
cowanthomasAug 31, 2025
How to fix noisy or stiff castors/brakes on Invacare Birdie EVO Lifting Systems?
- R
  robinsonmonicaAug 31, 2025
  Noisy or stiff castors/brakes usually indicate fluff or debris in the bearings. Replace the castors.
L
Linda GibsonAug 29, 2025
Why is my Invacare Lifting Systems actuator making unusual noises?
- V
  Victoria BlackAug 30, 2025
  An unusual noise from the actuator indicates that the boom or leg actuator is worn or damaged, or the spindle is bent. You will need to replace the actuator.
J
Jennifer AdamsAug 28, 2025
How to fix a loose Invacare Lifting Systems?
- C
  Christopher DunnAug 28, 2025
  If your patient lift feels loose, check the following: * Tighten the mast/base connection. * Tighten the mast/boom connection. * Tighten the screws of the tie-rods and/or pedal.
A
Angel ColonAug 27, 2025
Why does my Invacare Birdie EVO Lifting Systems beep and stop during lifting?
- P
  Philip DavisAug 27, 2025
  If the control unit emits a beeping sound during lifting and the motor stops, it means the maximum load has been exceeded. Reduce the load, and the lift should function normally.
J
Julie GutierrezAug 27, 2025
How to fix loose patient lift in Invacare Birdie EVO?
- K
  Kyle LeblancAug 27, 2025
  If your Invacare Lifting Systems patient lift feels loose, it could be due to a loose mast/base joint, mast/boom joint, or tie-rods. Check and tighten the mast/base connection, the mast/boom connection, and the screws of the rods and/or pedal.
C
cookamandaAug 25, 2025
What to do if boom will not lower during a power retraction of Invacare Birdie EVO Lifting Systems?
- J
  Jamie ConradAug 26, 2025
  If the boom will not lower during a power retraction, the shoulder bolt at the junction of the boom and mast may not be properly installed. Check the mast/boom connection.
C
christinakellyAug 25, 2025
What to do if the boom on my Invacare Birdie EVO Lifting Systems won't lower from the top?
- J
  John BrewerAug 25, 2025
  If the boom will not lower in the uppermost position, it requires a minimum weight load to lower. Pull down slightly on the boom.