PEDAL iSSi II INSTRUCTIONS
6400 West 105th Street Minneapolis, MN 55438 www.rideissi.com
13124 04/15
THANK YOU FOR PURCHASING ISSI PEDALS!
At iSSi
™
, we know the best way to improve a bike is to make it truly your own.
That’s why we fashion top notch equipment to help personalize the connection
between you and your bike. iSSi: it’s your bike; make it yours.
WARNING: CYCLING CAN BE DANGEROUS. BICYCLE PRODUCTS SHOULD
BE INSTALLED AND SERVICED BY A PROFESSIONAL MECHANIC. NEVER
MODIFY YOUR BICYCLE OR ACCESSORIES. READ AND FOLLOW ALL PRODUCT
INSTRUCTIONS AND WARNINGS INCLUDING INFORMATION ON THE
MANUFACTURER’S WEBSITE. INSPECT YOUR BICYCLE BEFORE EVERY RIDE.
ALWAYS WEAR A HELMET!.
WARNING: A loose, cracked, worn out, or crashed pedal can come off
of your bicycle crank leading to a loss of control that could cause serious injury.
Pedals that are damaged or worn out should not be used. Remove immediately
and inspect for damage. If you are unsure if your pedal is unsafe to ride, consult
your local bicycle dealer.
WARNING: Never ride in open-toed or open-heeled shoes as they don’t fully
support and secure your foot. Doing so could lead to a loss of control and serious
injury and/or death.
For additional product and safety information go to: www.rideissi.com/safety.
COMPATIBILITY
iSSi pedals are for cranksets with 9/16" pedal threads. iSSi pedals are designed
for use with iSSi cleats, Wellgo 98A cleats, and Shimano SPD
®
cleats.
iSSi cleats are compatible with all standard two-bolt SPD-style shoes.
INTENDED USE
iSSi pedals are intended for on- and off-road trail use, including
ASTM use Condition 3. This is a set of conditions for operation
of a bicycle that includes Condition 1 (paved roads) and
Condition 2 (unpaved and gravel roads) as well as rough trails,
rough unpaved roads, and rough terrain and unimproved trails
that require technical skills. Jumps and drops are intended to
be less than 61cm (24").
iSSi pedals are NOT intended for hardcore freeriding, extreme downhill, dirt
jumping, slopestyle, or other aggressive and/or extreme riding types.
TOOLS AND SUPPLIES
3mm and 6mm Allen wrenches
Grease
NOTE: Never use a cone wrench to remove or install a pedal.
NOTE: Pedal threads are different from left side and right side. The right-side
pedal has a right-hand thread (removes counterclockwise, installs clockwise).
The left-side pedal has a left-hand thread (removes clockwise, installs
counterclockwise). Additionally, the thread will appear to slope up toward
its tightening direction. Left-hand threads slope up to the left, while right-hand
threads slope up to the right.
INSTALLING PEDALS
1. Begin by identifying the right and left pedals. Look for “L” and “R” marking
on the pedal body. It is only stamped on one side of the pedal.
CAUTION: Do not attempt to install a right-side pedal into the left-side
crank or vise versa. Doing so could permanently damage your crank AND
pedal. Left-threaded pedals (threads sloping upward to the left) go to left
crank. Right-threaded pedals (threads sloping upward to the right) go to
right crank. See image at top if in doubt.
2. Heavily grease threads of both pedals.
3. Thread the right-side pedal into right crank by hand, CLOCKWISE.
4. To tighten fully, use the 6mm Allen wrench from the back of the pedal spindle.
Torque to 18Nm.
5. Repeat these steps for the left-side pedal, making sure to tighten by turning
COUNTER-CLOCKWISE.
NOTE: Periodically check both pedals for tightness and retighten according
to these instructions if necessary.
WARNING: Immediately discontinue using the pedals if excessive play
develops, the pedal body or spindle shows signs of cracking, or the pedal body
seems too tight or too loose on the spindle. Take your bicycle or pedals
to a professional bicycle mechanic for evaluation, service, or replacement.
(See Ongoing Maintenance.)
LIMITED WARRANTY
This iSSi product is warranted against defects in materials and workmanship
for three years from the date of retail purchase of the product, subject to the
limitations detailed below. Save your dated receipt for proof of purchase.
This warranty does NOT cover the following:
• Damage due to improper assembly or follow-up maintenance or lack of skill,
competence or experience of the user or assembler
• Products that have been modified, neglected, used in competition or for
commercial purposes, misused or abused, involved in accidents or anything
other than normal use
• Damage or deterioration to the paint, surface finish, aesthetics or appearance
of the product
• Normal wear and tear
• Labor required to remove and/or refit and re-adjust the product within the
bicycle assembly
• Installation of components, parts, or accessories not originally intended use
with or compatible with iSSi products.
This limited warranty is expressly limited to the repair or replacement
of a defective product, at the option of iSSi, and is the sole remedy of the
warranty. This limited warranty applies only to the original purchaser of the
iSSi product and is not transferrable. This warranty applies only to products
purchased through an authorized dealer or distributor. In no event shall iSSi
be liable for any loss, inconvenience or damage, whether direct, incidental,
consequential, or otherwise resulting from breach of any express or implied
warranty or condition, of merchantability, fitness for a particular purpose,
or otherwise with respect to our products except as set forth herein. This limited
warranty gives the consumer specific legal rights, and those rights and other
rights may vary from place to place. This limited warranty does not affect your
statutory rights.
TO THE EXTENT NOT PROHIBITED BY LAW, THESE WARRANTIES ARE
EXCLUSIVE AND THERE ARE NO OTHER EXPRESSOR IMPLIED WARRANTIES OR
CONDITIONS INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY
AND FITNESSFOR A PARTICULAR PURPOSE.
WARRANTY PROCESS
We will happily back up our products if there is a problem that is our fault.
If you and your shop think your iSSi product is worthy of a warranty inspection,
please return the product to the original place of purchase, accompanied by
a sales receipt.
3
For rough
off-road riding
and jumps less
than 24" (61cm)
ASTM F2043
To Next Page
Need help?
General