Multilink
®
Multilink
®
Primer A/B
Metal/Zirconia Primer
Instructions for Use
Description
Multilink is a self-curing and self-etching luting composite system for
the adhesive luting of indirect restorations made of metal, metal-
ceramic, all-ceramic and composite. Multilink has been developed for
applications where light curing is not possible or difficult and for
indications where high retention and bond strength are desired.
Multilink is applied together with the Multilink Primer A/B. For this
purpose, the two Multilink Primer components A and B are mixed in a
1:1 ratio directly before the application. Subsequently, the mixture is
applied to the dentin and the enamel.
Multilink features a reliable and fast self-cure with excellent
mechanical properties and a long-term hydrolysis-resistant matrix
due to its pure composition of composites. Together with the self-
curing primer, very good bond strength values and a good marginal
adaptation is achieved.
The Metal/Zirconia Primer is recommended as a coupling reagent to
achieve a stronger bond to precious and non-precious alloys, as well
as all-ceramics made of zirconium and aluminium oxide.
Shades
Multilink is available in three shades with different degrees of
translucency:
– Transparent (high translucency)
– Yellow (high translucency)
– Opaque (low translucency)
Working and setting time
The working and setting times depend on the ambient temperature.
The following times apply after the two pastes have been mixed
(mixing time approx. 20 sec):
Mixing ratio/Dosage
The single pastes are dispensed from the Multilink double-push
syringe and mixed in a 1:1 ratio.
Multilink Primer A and Multilink Primer B are mixed in a 1:1 ratio
(e.g. 1 drop of Primer A + 1 drop of Primer B) or a multiple of it.
– Self-curing resin based dental
luting material
Self-curing and self-etching primer
– Selbsthärtendes zahnärztliches
Befestigungscomposite
Selbsthärtender und selbstätzender
Primer
– Composite autopolymérisant pour
le collage des restaurations
dentaires
Primer automordançant,
autopolymérisable
– Cemento composito autoindurente
Primer autoindurente e
automordenzante
– Material de fijación dental en base
a resina autopolimerizable
Primer autopolimerizable y
autograbante
– Compósito de cimentação
autopolimerizável
Primer autocondicionante e
autopolimerizável
– Självhärdande resinbaser
at dentalt
cement
Självhärdande och självetsande
primer
– Kemisk hærdende dental
plastretentionscement
Kemisk hærdende og selvætsende
Primer
– Kemialliskovetteinen
yhdistelmämuovisementti
hammaslääketieteelliseen käyttöön
Kemialliskovetteinen ja itse-etsaav
a
primer
– Selvherdende odontologisk
sementeringsmateriale
Selvherdende og selvetsende primer
–
Zelfuithardende bevestigingskunst
-
stof voor tandheelkundig gebruik
Zelfuithardende en zelfetsende
primer
– Ρητινούχ
ο
,
οδοντιατρικ υλικ
συγκλλησησ, χηµικά πολυµεριζµενο.
Ενεργοποιητήσ (primer) xηµικά
πολυµεριζµενοσ µε ενεργοποιητέσ
αδροποίησησ (self-etc
hing)
576484/1005/WE3/G
English
F
or dental use only.
Caution: U.S. Federal Law restricts this device to sale
by or on the order of a licensed dentist.
Made in Liechtenstein
Ivoclar Vivadent AG, FL-9494 Schaan/Liechtenstein
Complies with / entspricht:
ISO 4049, ANSI/ADA Spec. No. 27
Instructions for Use
Gebrauchsinformation
Mode d’emploi
Istruzioni d’uso
Instrucciones de Uso
Instruções de Uso
Bruksanvisning
Brugsanvisning
Käyttöohjeet
Bruksanvisning
Productinformatie
Oδηγίεσ Xρήσεωσ
Working time (with-
(out mixing time)
Curing time (without
working time)
Room temperature
23°C ±1°C
180 ± 30 sec
300 ± 30 sec
Intraoral
approx. 37°C ± 1°C
120 ± 30 sec
180 ± 30 sec
To Next Page
Need help?
General
