What to do if the PID display is turned off on my Izzo Coffee Maker?
If the PID display is off on your Izzo Coffee Maker, ensure the main power switch is on and the outlet has power. Also, make sure the water reservoir is filled with cold softened water, or if plumbed in, that the water supply is turned on. If these are fine, try turning the machine off for 3 seconds and then back on to reset it.
Why is my Izzo Alex-2 Coffee Maker not heating?
If your Izzo Coffee Maker isn't heating, ensure it's plugged into a working outlet and the main power switch has been on for at least 15 minutes. Also, make sure the water supply is on. If it was off, turn it back on, then turn the power switch off, unplug the machine, wait 5 seconds, plug it back in, and turn the power switch back on. Check the resettable hi-limit switch on the left side of the boiler and firmly press the red reset button. Finally, check the PID settings to ensure they are programmed correctly.
What to do if there is no steam from the steam wand of my Izzo Alex-2?
If there's no steam from the steam wand of your Izzo Coffee Maker, first, ensure the main power switch has been on for at least 15 minutes and that the upper gauge shows a steam pressure of about 1.2 bar. Then, check the steam tip for blockages and clean the holes with a paper clip. Also, inspect the steam wand for blockages by unscrewing the steam tip and checking for dried milk inside, ensuring the white Teflon tube is clear. Finally, check the steam knob for proper operation by removing the end cap and verifying the c-clip is attached.
Why is espresso coming out too slow from my Izzo Coffee Maker?
If the espresso is coming out too slowly or not at all from your Izzo Coffee Maker, activate the brew lever and check the pump pressure, ensuring it's set to the recommended 9 bar. If the pump pressure is good, try adjusting the grind coarser. Also, ensure that the insert basket is not overfilled with coffee and that you are tamping with no more than 30lbs of pressure.
What to do if espresso is coming out too fast from my Izzo Alex-2?
If espresso is coming out too fast from your Izzo Coffee Maker, activate the brew lever and check the pump pressure, ensuring it's at the recommended setting of 9 bar. If the pump pressure is good, try adjusting the grind finer. Also, make sure the insert basket is filled with the proper amount of coffee and you are tamping with 30lbs of pressure.
How to fix leaking around the portafilter when brewing with my Izzo Alex-2?
To fix leaking around the portafilter when brewing with your Izzo Coffee Maker, ensure the portafilter is tightly locked into the grouphead as far right as it can go. Also, make sure the portafilter basket is not overfilled with coffee. If the problem persists, replace the group gasket, especially if it's more than a year old.
Why is there no water from the hot water wand of my Izzo Alex-2?
If there's no water from the hot water wand of your Izzo Coffee Maker, first ensure the main power switch has been on for at least 15 minutes. Check the upper gauge for steam pressure, which should be about 1.2 bar. Then, check the hot water knob for proper operation by removing the end cap and verifying the c-clip is attached.
What causes vapor lock in my Izzo Alex-2?
Vapor lock in your Izzo Coffee Maker is caused by a sticking vacuum breaker valve.
What does it mean if steam is continually discharged into the drip tray of my Izzo Alex-2 Coffee Maker?
If steam continues to fill the drip tray of your Izzo Coffee Maker after a few minutes, the vacuum breaker valve should be replaced.
What does it mean when the steam gauge shows full pressure but drops to zero when the steam knob is opened on my Izzo Alex-2?
If the steam gauge shows full pressure on your Izzo Coffee Maker but drops to zero when the steam knob is opened, this is caused by a sticking vacuum breaker valve.
General| Brand | Izzo |
|---|---|
| Model | Alex-2 |
| Category | Coffee Maker |
| Language | English |
To Next Page
