JABSCO 23680-4003 - User Manual

To Next Page

MODELS:

23680-4003 12V DC

23680-4103 24V DC

COMMERCIAL DUTY

WATER

PUPPY

FEATURES:

Continuous rated, medium duty pumps for

bilge and general purpose use.

z ISO 8846 MARINE (Ignition protection).

z ISO 8849 MARINE (Bilge pump standard).

z Small bilge debris present no problem to

these bronze bodied, flexible impeller

pumps.

z Simple design means fewer wearing

parts.

z 32 lpm (6.5 UK gpm) output @ 3m (10ft)

head.

z Self priming to 1.2m (4 ft).

INSTALLATION INSTRUCTIONS

Jabsco Water Puppy can be mounted on any flat

surface. Fit the pump in a dry, well ventilated

position where there is full access for service. If

installed in a vertical position the motor must be

above the pump head. Use the rubber grommets

provided to minimise vibration, do not overtighten the

mounting screws.

Secure 25mm (1”) id hose either direct to the

discharge ports or to ½” BSP male threaded fittings

using stainless steel hose clamps. Use spiral

reinforced hose (with a smooth internal bore) that will

not collapse under suction, or rigid or semi rigid

pipework systems. The pipework must be compatible

with the liquid being pumped. Pipe runs should be

kept as straight and short as possible, avoiding rising

and dipping over obstructions. Fit a strainer on the

inlet hose to prevent larger debris from entering the

pump.

WIRING INSTRUCTIONS

Make all electrical connections in dry locations,

connections in humid environments should be sealed

to prevent corrosion. Protect the circuit with a

correctly rated fuse or circuit breaker in the orange

positive (+) lead as close as possible to the power

source. Connect the black motor wire to the negative

(-) battery terminal. Inadequate voltage at the motor

terminals when the pump is running (not less than

10% below rated voltage at full load) due to partially

discharged batteries or insufficient cable size may

result in blowing fuses, failure to start or poor pump

performance.

WARNING: If the fuse fails

repeatedly do not fit a heavier fuse or

bridge the fuse terminals with silver

paper or metal wire. Failure to observe

this instruction may result in a fire

hazard due to overheating of cables.

WARNING: All marine pumps

discharging overboard must be

installed with the overboard discharge

well above both static and heeled

waterlines.

m ft lpm UK gpm

2735 7.7

31032 7

41330 6.6

62025 5.5

WATER PUPPY PERFORMANCE

TOTAL HEAD

WATER PUPPY

Approximate performance for new pump,

running water at 20°C with fully charged battery

WARNING: Do not use any Jabsco

pump for petrol, petroleum products or

any products with a flash point below

37°C (98°F), explosion or death may

occur.

Need help?

Do you have a question about the JABSCO 23680-4003 and is the answer not in the manual?

Summary

Product Features

Ignition Protection and Bilge Standards

Features ISO 8846 MARINE (Ignition protection) and ISO 8849 MARINE (Bilge pump standard).

Pump Design and Performance

Bronze bodied, flexible impeller pumps handling small bilge debris with simple design.

Output and Priming Capabilities

Offers 32 lpm (6.5 UK gpm) output at 3m head and self-priming to 1.2m.

Installation Instructions

Mounting and Ventilation

Mount pump on flat surface in dry, ventilated position with motor above pump head.

Hose and Pipework Requirements

Use 25mm (1") hose or BSP fittings with smooth bore hose; keep pipe runs short.

Wiring Instructions

Electrical Connection Guidelines

Make connections in dry locations, seal humid environments, protect circuit with fuse.

Voltage and Performance Considerations

Ensure adequate voltage to motor to prevent fuse blowing or poor performance.

Electrical Specifications

Model Specific Wiring Data

Details voltage, amp draw, fuse size, wire size, and cable length for models.

Dimensional Drawing and Parts List

Pump Component Identification

Provides a breakdown of pump parts, including key components and their part numbers.